0
Add your answer:
Earn +20 pts
Where is the PCV valve on a 1993 Buick Regal 3.1L?
On a 1993 Buick Regal 3.1L, the PCV valve is located on the intake manifold. It is situated underneath the MAP sensor.
1996 buick regal with a p0108 error trouble code?
Trouble code P0108 means: MAP Sensor Circuit High Input
Have a 1991 buick regal custom 31L sometimes it will just up and die while driving but will start again doesn't do it all the time any clue why?
I have the same issue it is the map sensor
How do you locate and replace the map sensor in a 95 Buick LeSabre?
Don't think yours will have a MAP sensor. It will have a MAF sensor, and it is attached to the air filter housing.
Where is the location of the MAP sensor on a 1990 Buick LeSabre?
After consulting several sources, someone finally called a local Buick dealer who informed me that a 1990 LeSabre does NOT have a map sensor, it was the Mass Air Flow sensor that needs replacing.
Where is the map sensor in a 2001 ford ranger edge 4.0L V6?
The 2001 Ford Ranger 4.0 liter V-6 engine map sensor is located on the firewall in the engine compartment. The map sensor will be on the drivers side of the firewall.
Where is the MAP sensor of a Nissan Maxima 2001?
The MAP sensor is mounted at the rear of the left-bank (front) cylinder head.
Where is the map sensor located on a 94 Buick Roadmaster?
Powertrain Control Module (PCM)
Where is the Pcv valve located on a 1998 Buick regal?
On the passengers' side of the car you'll have to lift the plastic cover over the engine and look at the MAP sensor located at the passengers' end of the plastic cover (black in color and held in place by plastic clips--making up the entire MAP sensor assembly). There are three wires connected to the MAP sensor. Remove the wire assembly first. The MAP sensor is removed by twisting it counter clockwise (a small pair of channel locks might assist in removing it). There is a large spring just under the MAP sensor that pushes down on the PCV valve. Remove the MAP sensor and spring and then you can access the PCV valve. You might need a pair of plyers to remove the PCV valve. Installation of the MAP sensor assembly is done by replacing the spring, putting the MAP sensor assembly on the spring, assure the assembly is in the counterclockwise position and twisting it clockwise to reinstall.
Why would your 1995 Buick Regal jerk the entire time you are driving as if you are accelerating and decelerating at the same time?
my 1995 buick regal is starting to do it too but mainly when going uphill or accelerating hope someone answeers soonAnswerI am not sure if this is the same problem, but my 95 regal had what I would call a "surging" or stuttering problem...This was supposedly caused by a spark plug wire shorting out at the boot thus causing a missfire... AnswerMy 1995 Buick Regal was doing this. Mine was a transmission problem. I didn't need a whole new transmission, but I did need to replace the lines because they were leaking fluid. You should definitely get it checked out. AnswerJust had my 2002 into a Transmission shop. The brake switch needed adjusting. I had no check engine light. You might want to get the brake switch checked. Check the map sensor. Mine was doing that, and after having trans check and several parts replaced on it, it ended up being the map sensor
Where is the MAP sensor located on a 96 Buick LeSabre?
Passenger side of black plastic intake plenum.
Where is the map sensor on a '93 Buick Century?
On the firewall on the right side. if the car is 3.3l v6 then the car doesn't have a map sensor but it does have a mass air flow sensor the code is the same for both of them only a 2.3 has the map sensor so don't be fooled by this by code 34 the chilton book is very helpful
