0
My current microwave oven causes my circuit breaker to trip if I use it at the same time as my toaster oven. Will this microwave solve that problem?
Wiki User
∙ 14y ago
It's doubtful; I wouldn't be able to answer that for sure unless I knew the particulars of your set-up (what is your microwave/toaster's draw? what kind of breaker do you have? etc.), but I don't see any reason why this microwave would help that situation.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What would cause circuit breaker to trip in new box from old box?
A circuit breaker will trip if it is faulty or if the connected circuit has a short circuit or a connected device is trying to draw more current than the breaker rating. If you disconnect the output wire from the breaker and it still trips, it is a faulty breaker. If the breaker is tripping immediately when it is turned on then start disconnecting elements of the circuit to see what might be causing the problem. If everything was working and now isn't, it is likely that the wire from the breaker is nicked where it exits the box and is shorting to the feedthru connector.
What device can break an electric circuit?
There are 2 different types of these devices: circuit breakers (which can be reset after the problem is fixed) and fuses (which must be replaced after the problem is fixed).
My circuit breaker keeps popping I have replace the 2-prong outlet with a 4-outlets and why is it still popping?
A breaker trips when there is too much current. If you unplug everything on the circuit and the breaker still trips then you have a wiring problem or a bad breaker. From your description it is not possible to be certain if the problem started when you installed new outlet or previously. You have to describe your problem in better detail to get a good answer. When you have a circuit that trips the corresponding breaker, you need to go through each outlet on the circuit and rule it out as the problem. This can be done by pulling each outlet, from the wall and systematically remove wires from outlets while power is off and determining when problem goes away.
Can you use 70amp breaker for 40amp device?
The purpose of a circuit breaker in a panel is to protect the wiring and devices like switches, outlets and other devices that are part of that circuit. It isn't unusual to plug in an appliance into a circuit whose amperage rating is less than the breaker protection. If such an appliance doesn't have its own over-current protection it may well "fry" in an over current situation. However, if your 40 Amp device is directly connect to the 70 A circuit and has no over-current protection on its own you are risking a serious problem. If your 40 A device is on this dedicated circuit you should protect it with a properly sized breaker.
Parking lights will not turn off is it a relay or circuit breaker?
It is a relay or switch problem. A circuit breaker or fuse won't keep a light on.
Possible electrical problem will my microwave oven be okay?
Check the circuit breaker to see if it tripped.
Can a motorized lift chair cause a breaker to trip?
A breaker trips because the circuit load has tried to draw more current that the circuit is designed to operate at. You have to establish what the total current draw of the device is. This can be found on the manufactures label. There it will state what the normal amperage draw is for the specific piece of equipment. If the breaker has tripped, look for the cause and rectify the problem before resetting the breaker. If you found the problem and corrected the cause, the breaker will reset and stay in the on position.
What would cause circuit breaker to trip in new box from old box?
A circuit breaker will trip if it is faulty or if the connected circuit has a short circuit or a connected device is trying to draw more current than the breaker rating. If you disconnect the output wire from the breaker and it still trips, it is a faulty breaker. If the breaker is tripping immediately when it is turned on then start disconnecting elements of the circuit to see what might be causing the problem. If everything was working and now isn't, it is likely that the wire from the breaker is nicked where it exits the box and is shorting to the feedthru connector.
My circuit breaker keeps popping I have replace the 2-prong outlet with a 4-outlets and why is it still popping?
A breaker trips when there is too much current. If you unplug everything on the circuit and the breaker still trips then you have a wiring problem or a bad breaker. From your description it is not possible to be certain if the problem started when you installed new outlet or previously. You have to describe your problem in better detail to get a good answer. When you have a circuit that trips the corresponding breaker, you need to go through each outlet on the circuit and rule it out as the problem. This can be done by pulling each outlet, from the wall and systematically remove wires from outlets while power is off and determining when problem goes away.
What device can break an electric circuit?
There are 2 different types of these devices: circuit breakers (which can be reset after the problem is fixed) and fuses (which must be replaced after the problem is fixed).
Can you use 70amp breaker for 40amp device?
The purpose of a circuit breaker in a panel is to protect the wiring and devices like switches, outlets and other devices that are part of that circuit. It isn't unusual to plug in an appliance into a circuit whose amperage rating is less than the breaker protection. If such an appliance doesn't have its own over-current protection it may well "fry" in an over current situation. However, if your 40 Amp device is directly connect to the 70 A circuit and has no over-current protection on its own you are risking a serious problem. If your 40 A device is on this dedicated circuit you should protect it with a properly sized breaker.
Parking lights will not turn off is it a relay or circuit breaker?
It is a relay or switch problem. A circuit breaker or fuse won't keep a light on.
Why does my refrigerator keep tripping the breaker?
The most likely possibility is the refrigerator has a problem and needs to be fixed. Another possibility is the refrigerator is on a circuit that does not have enough current capacity to operate it and other appliances that are on the same circuit.
Refrigerator kicks off breaker on occasion it is a 30 amp breaker does this sound like a refrig or a wiring problem?
If there is nothing else on the circuit the odds are it kicks off when the compressor starts. This is a motor and the starting current is higher running current. The breaker senses this surge and trips. Either the compressor is drawing more current because of a problem with shunt somewhere in the winding of the motor or the breaker is tripping because it has a problem that has essentially made it more sensitive to current and is tripping on a lower current than it is rated for. The cheapest fix is to replace the breaker. If you know what you are doing you coudl just switch breakers with an equally rated breaker in the electric panel. If you don't know what you are doing find someone who does. If this doesn't fix the problem it is likely a faulty compressor.
How fuses differ from circuit breakers?
A fuse contains a component that melts or breaks in some other fashion when excessive current flows through it. This breaks the electrical circuit. A fuse that has functioned in this way can never be reused. A circuit breaker is a mechanical switch that opens, breaking the flow of electricity when the current goes above a set point. A circuit breaker can be reused by simply closing the switch again once the problem causing excessive current has been taken care of.
How does a circuit breaker operate?
A circuit breaker can be magnetic; the higher the current is the stronger the magnetic field will be, if the magnetic field gets strong enough it will pull open the circuit. A circuit breaker can also be thermal; as current travels through the circuit heat is generated (higher current = more heat), in the breaker there is two different kinds of metal bonded together, each will expand and contract at different rates, since they are bonded together they will bend and trip the circuit open. A circuit breaker can be a combination of magnetic and thermal.
Where is the circuit breaker located on a 1967 Cadillac Fleetwood?
There is only one circuit breaker to my knowledge and it is for the power windows. I have a 1968 Fleetwood and it is very similar. What exactly is the problem?
