0
SkyScan Model 31981B TO START THE CLOCK:
1. Insert 2 AAA batteries with proper polarity (+) and (-)as indicated In the battery compartment.
2. The LCD goes to default time and calendar 12:00:00AM (time) and 1-1 (Jan 1 2003).
The alarm time is 6:00 AM.
Default time zone is PST, default temp. readout Is degree F.
3 The clock takes the temperature reading immediately then starts to search for the WWVB signal. Remarks: If you immediately manually set the time / alarm time / calendar the clock will slop its initial reception of the WWVB signet. It will resume to the WWVB reception automatically when the clock exits SET mode and no other button is pressed for 5 seconds.
TO SELECT THE TIME ZONE:
1. Press TIME ZONE button once, the LCD shows the time zone (the default time zone is PST).
2- Press + or - - to set the time zone (PST>MST>CST>EST)
3. Press the TIME ZONE or SET button to go back to the time display or it will automatically go back to the time display in 5 seconds.
TO SET TIME, CALENDAR, 12/24HR AND C/F:
1. Press the SET button once to set the Year: digits show '2003" and blink. Press + or - - to set the year.
2. Press the SET button again to set the Date : small digits show " 1 - 1" (i.e. Jan 1st) and blink. Press + or - - to set the date. Press and hold + or - will increase the increment or decrement at a faster rate.
3. Press the SET button again to set the Time : large digits in HR : MIN will show and blink.
Press + or - to set the clock to the current time. Press and hold + or - will increase increment or decrement at a faster rate.
4. Press the SET button again to set 12 / 24 HR readout. Upper LCD shows "l2Hr" and blink.
Press + or - to choose 12HR or 24 HR time display format.
5. Press the SET button again to select C/Freadout: the temperature readout (i.e. 68F) will blink. Press + or - to choose readout (i.e. 68F or 20C ). The default readout is In degree F.
6. Press the SET button again to exit the setting mode and return to the normal display. Or it will automatically return in 5 seconds. **Special attention for usage in Arizona and Indiana.**
Part of Arizona and Indiana do not have Daylight Saving Time (DST).
Please slide the DST switch inside the battery compartment to OFF if the clock is used in these states.
TO SET ALARM TIME ;
1. To read your alarm time: press + or - once, the lower Month and Date digits will change to alarm time digits.
2. To set the alarm time: press + or - again, the alarm digits will blink, Press + or - - to set your alarm time. Press and hold + or - will increase the increment or decrement at a faster rate..
3. Alter you set the alarm, the clock will go back to the normal display automatically in 5 seconds.
TO TURN ON/OFF THE ALARM:
1. To use snooze alarm
Press the SNOOZE / AL ON/0FF button until SNZ and (((o))) show on lower LCD.
When the alarm beeps, press SNOOZE / LIGHT bar. The alarm will Sound again when the snooze period
is over. (See "To Program the Snooze Alarm " below)
When the alarm beeps, press any key at the front to stop the alarm. The snooze alarm will turn on the following day at the same time.
2. To turn on alarm
Press the SNOOZE /AL ON/OFF button until (((o))) shows on lower LCD.
When the alarm beeps, press SNOOZE / LIGHT. The alarm will turn on the following day at the same time.
3. To disable the alarm permanently:
Press the SNOOZE / AL ON / 0FFbutton until the SNZ and (((o))) clear from the lower LCD.
TO PROGRAM THE SNOOZE ALARM:
1. Press and hold the SNOOZE I LIGHT bar for 3-4 seconds. The small display will blink and show 05 (minutes) the default snooze duration. Press + or - to set the snooze duration from 5 minutes to 60 minutes.
Note: The minimum snooze duration is 5 minutes.
2. Press the SNOOZE I LIGHT bar once to go back to the normal display or the clock will auto exit if no further buttons are pressed after 5 seconds.
What else can I help you with?
Instructions for skyscan atomic clock model 26600?
To set the time on the Skyscan atomic clock model 26600, press the "SET" button until the time zone is displayed on the screen. Use the "+" and "-" buttons to adjust the time zone, and press "SET" again. The clock should then synchronize with the atomic time signal and display the correct time.
SkyScan Atomic clock model 86715?
The SkyScan Atomic Clock model 86715 receives radio signals from atomic clocks to stay accurate. It automatically adjusts for Daylight Saving Time and has a large display for easy reading. It also features an alarm with snooze function.
SkyScan Atomic clock will not display outside temperature Put in fresh batteries and clock still does not display anything other than 2 dashes?
I had the same thing happen. I replaced the batteries in the outdoor sensor, but just got the two dashes on the clock that should display the outside temperature. After I replaced the batteries in the clock itself, the outside temperature then showed up properly on the clock. I also took all batteries out of both devices and replaced them in the order recommended in the directions on the back of the clock. I hope that helps.
How do you set a Vollmond Atomic Wall Clock?
To set a Vollmond Atomic Wall Clock, first install the batteries and wait for it to receive a signal from the atomic clock. Once the time is set automatically, you can manually adjust it if necessary using the buttons on the clock. Refer to the user manual for specific instructions for your model.
How do you reset the time on an atomic clock when daylight savings time ends?
You don't do a thing!! My husband replaced the batteries on our the other night, and after a few minutes (I assume it got a radio signal update) it reset itself! Pretty cool... You are wrong!!!!! I asked for a manual reset, not waiting for the clock to maybe catch up.
How do you find instructions for SkyScan Atomic Clock model 31310?
http://skyscaninfo.com/content/manuals/33-model-31310t.html
How do you find instructions for the Skyscan atomic clock model 87315?
Skyscan model 87315 does not have a manual on the Skyscan website. Use the manual for model 87310 and skip over the temperature transmitter instructions. The instructions for the setup buttons on the back work for 87315. I received the following in an email from the SkyScan website customer service. The clock referenced has a different frame, but the same functions and displays. You can use the manual for model 86730 this is the upgrade from your model and the functions are the same.
Instructions for skyscan atomic clock model 26600?
To set the time on the Skyscan atomic clock model 26600, press the "SET" button until the time zone is displayed on the screen. Use the "+" and "-" buttons to adjust the time zone, and press "SET" again. The clock should then synchronize with the atomic time signal and display the correct time.
How do you find insructions for Skyscan atomic clock model 87315?
To find instructions for the Skyscan atomic clock model 87315, you can visit the manufacturer's website and look for a downloadable manual in the support section. You can also try contacting the manufacturer directly for a digital or physical copy of the manual. Additionally, you may find user-generated guides or videos online that provide step-by-step instructions for setting up and using the clock.
Instuctions for SkyScan Atomic clock model 87801?
This doesn't answer the question. We can't refer them to another link. Please revise, remove this comment, and resubmit. The instructions for the SkyScan Atomic clock model 87801 can be found here in the form of a .pdf document: skyscanatomicclocks.com/manuals/87800-01.pdfAlso included in this manual is the 87800 model; this manual covers both clocks.
Skyscan atomic clock model 86722ALU instructions?
To set the time on the Skyscan Atomic Clock model 86722ALU, first, insert the required batteries. Make sure the clock is in the Time Zone mode. Press and hold the SET button until the time zone begins flashing. Use the + and - buttons to adjust the time to your correct time zone. Press the SET button to confirm.
How do you turn off the alarm on model 31269 skyscan atomic clock?
To turn off the alarm on the model 31269 Skyscan atomic clock, press the "ALARM" button until you see the alarm icon disappear from the display. If your clock has a snooze function, pressing the "SNOOZE" button will silence the alarm temporarily, but you'll need to deactivate the alarm entirely by using the "ALARM" button. Make sure to check the manual for any specific instructions related to your model.
Where can I obtain instructions for the operation of a Atomic clock?
http://www.lacrossetechnology.com/8117it/manual.pdf This has the instructions for your atomic clock.
SkyScan Atomic clock model 86715?
The SkyScan Atomic Clock model 86715 receives radio signals from atomic clocks to stay accurate. It automatically adjusts for Daylight Saving Time and has a large display for easy reading. It also features an alarm with snooze function.
How do you change the battery in the Sky scan Atomic clock?
To change the battery in a SkyScan Atomic clock, you typically need to remove the battery cover on the back of the clock, take out the old battery, and insert a new one following the correct polarity. Refer to the clock's manual for specific instructions as methods may vary between models.
Instructions for SioScan atomic clock Model 86715?
Well, honey, first things first - find the manual. Then, set the time zone, date, and time using the buttons on the clock. Make sure to place the clock in an area with good reception for the atomic signal. And voila, you've got yourself a perfectly synced atomic clock. Now go out there and conquer the world, one precise second at a time!
Model86722alu outside temp not working readsofl?
Skyscan Atomic Clock Model 86722ALU needs a reset after a battery change, or needs a battery change.
