answersLogoWhite

0

SkyScan Model 31981B TO START THE CLOCK:

1. Insert 2 AAA batteries with proper polarity (+) and (-)as indicated In the battery compartment.

2. The LCD goes to default time and calendar 12:00:00AM (time) and 1-1 (Jan 1 2003).

The alarm time is 6:00 AM.

Default time zone is PST, default temp. readout Is degree F.

3 The clock takes the temperature reading immediately then starts to search for the WWVB signal. Remarks: If you immediately manually set the time / alarm time / calendar the clock will slop its initial reception of the WWVB signet. It will resume to the WWVB reception automatically when the clock exits SET mode and no other button is pressed for 5 seconds.

TO SELECT THE TIME ZONE:

1. Press TIME ZONE button once, the LCD shows the time zone (the default time zone is PST).

2- Press + or - - to set the time zone (PST>MST>CST>EST)

3. Press the TIME ZONE or SET button to go back to the time display or it will automatically go back to the time display in 5 seconds.

TO SET TIME, CALENDAR, 12/24HR AND C/F:

1. Press the SET button once to set the Year: digits show '2003" and blink. Press + or - - to set the year.

2. Press the SET button again to set the Date : small digits show " 1 - 1" (i.e. Jan 1st) and blink. Press + or - - to set the date. Press and hold + or - will increase the increment or decrement at a faster rate.

3. Press the SET button again to set the Time : large digits in HR : MIN will show and blink.

Press + or - to set the clock to the current time. Press and hold + or - will increase increment or decrement at a faster rate.

4. Press the SET button again to set 12 / 24 HR readout. Upper LCD shows "l2Hr" and blink.

Press + or - to choose 12HR or 24 HR time display format.

5. Press the SET button again to select C/Freadout: the temperature readout (i.e. 68F) will blink. Press + or - to choose readout (i.e. 68F or 20C ). The default readout is In degree F.

6. Press the SET button again to exit the setting mode and return to the normal display. Or it will automatically return in 5 seconds. **Special attention for usage in Arizona and Indiana.**

Part of Arizona and Indiana do not have Daylight Saving Time (DST).

Please slide the DST switch inside the battery compartment to OFF if the clock is used in these states.

TO SET ALARM TIME ;

1. To read your alarm time: press + or - once, the lower Month and Date digits will change to alarm time digits.

2. To set the alarm time: press + or - again, the alarm digits will blink, Press + or - - to set your alarm time. Press and hold + or - will increase the increment or decrement at a faster rate..

3. Alter you set the alarm, the clock will go back to the normal display automatically in 5 seconds.

TO TURN ON/OFF THE ALARM:

1. To use snooze alarm

Press the SNOOZE / AL ON/0FF button until SNZ and (((o))) show on lower LCD.

When the alarm beeps, press SNOOZE / LIGHT bar. The alarm will Sound again when the snooze period

is over. (See "To Program the Snooze Alarm " below)

When the alarm beeps, press any key at the front to stop the alarm. The snooze alarm will turn on the following day at the same time.

2. To turn on alarm

Press the SNOOZE /AL ON/OFF button until (((o))) shows on lower LCD.

When the alarm beeps, press SNOOZE / LIGHT. The alarm will turn on the following day at the same time.

3. To disable the alarm permanently:

Press the SNOOZE / AL ON / 0FFbutton until the SNZ and (((o))) clear from the lower LCD.

TO PROGRAM THE SNOOZE ALARM:

1. Press and hold the SNOOZE I LIGHT bar for 3-4 seconds. The small display will blink and show 05 (minutes) the default snooze duration. Press + or - to set the snooze duration from 5 minutes to 60 minutes.

Note: The minimum snooze duration is 5 minutes.

2. Press the SNOOZE I LIGHT bar once to go back to the normal display or the clock will auto exit if no further buttons are pressed after 5 seconds.

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Natural Sciences

Instructions for skyscan atomic clock model 26600?

To set the time on the Skyscan atomic clock model 26600, press the "SET" button until the time zone is displayed on the screen. Use the "+" and "-" buttons to adjust the time zone, and press "SET" again. The clock should then synchronize with the atomic time signal and display the correct time.


SkyScan Atomic clock model 86715?

The SkyScan Atomic Clock model 86715 receives radio signals from atomic clocks to stay accurate. It automatically adjusts for Daylight Saving Time and has a large display for easy reading. It also features an alarm with snooze function.


How do you set skyscan Atomic Clock's daylight savings for model 38229-1?

To set the daylight saving time on the Skyscan Atomic Clock model 38229-1, press and hold the "SET" button until the time display begins to flash. Use the "UP" or "DOWN" buttons to navigate to the DST (Daylight Saving Time) setting, then select "ON" or "OFF" as desired. Press the "SET" button again to confirm your choice, and the clock will automatically adjust the time accordingly. Make sure to check the manual for any specific instructions related to your model.


SkyScan Atomic clock will not display outside temperature Put in fresh batteries and clock still does not display anything other than 2 dashes?

I had the same thing happen. I replaced the batteries in the outdoor sensor, but just got the two dashes on the clock that should display the outside temperature. After I replaced the batteries in the clock itself, the outside temperature then showed up properly on the clock. I also took all batteries out of both devices and replaced them in the order recommended in the directions on the back of the clock. I hope that helps.


How do i turn off daylight savings time on sky scan clock 86742?

To turn off Daylight Saving Time on the Sky Scan Clock model 86742, locate the "DST" or "Daylight Saving Time" button on the back or bottom of the clock. Press this button to toggle the setting off. If your clock has a menu, you may need to navigate to the time settings to find the DST option. After adjusting, ensure to check that the time displays correctly.

Related Questions

How do you find instructions for SkyScan Atomic Clock model 31310?

http://skyscaninfo.com/content/manuals/33-model-31310t.html


How do you find instructions for the Skyscan atomic clock model 87315?

Skyscan model 87315 does not have a manual on the Skyscan website. Use the manual for model 87310 and skip over the temperature transmitter instructions. The instructions for the setup buttons on the back work for 87315. I received the following in an email from the SkyScan website customer service. The clock referenced has a different frame, but the same functions and displays. You can use the manual for model 86730 this is the upgrade from your model and the functions are the same.


Instructions for skyscan atomic clock model 26600?

To set the time on the Skyscan atomic clock model 26600, press the "SET" button until the time zone is displayed on the screen. Use the "+" and "-" buttons to adjust the time zone, and press "SET" again. The clock should then synchronize with the atomic time signal and display the correct time.


How do you find insructions for Skyscan atomic clock model 87315?

To find instructions for the Skyscan atomic clock model 87315, you can visit the manufacturer's website and look for a downloadable manual in the support section. You can also try contacting the manufacturer directly for a digital or physical copy of the manual. Additionally, you may find user-generated guides or videos online that provide step-by-step instructions for setting up and using the clock.


Instuctions for SkyScan Atomic clock model 87801?

This doesn't answer the question. We can't refer them to another link. Please revise, remove this comment, and resubmit. The instructions for the SkyScan Atomic clock model 87801 can be found here in the form of a .pdf document: skyscanatomicclocks.com/manuals/87800-01.pdfAlso included in this manual is the 87800 model; this manual covers both clocks.


Skyscan atomic clock model 86722ALU instructions?

To set the time on the Skyscan Atomic Clock model 86722ALU, first, insert the required batteries. Make sure the clock is in the Time Zone mode. Press and hold the SET button until the time zone begins flashing. Use the + and - buttons to adjust the time to your correct time zone. Press the SET button to confirm.


How do you turn off the alarm on model 31269 skyscan atomic clock?

To turn off the alarm on the model 31269 Skyscan atomic clock, press the "ALARM" button until you see the alarm icon disappear from the display. If your clock has a snooze function, pressing the "SNOOZE" button will silence the alarm temporarily, but you'll need to deactivate the alarm entirely by using the "ALARM" button. Make sure to check the manual for any specific instructions related to your model.


How do you set time in skyscan atomic clock model 86715?

To set the time on the Skyscan atomic clock model 86715, first, ensure the clock is plugged in and powered on. Press the "SET" button, then use the "HOUR" and "MINUTE" buttons to adjust the time. After setting the correct time, press "SET" again to confirm the changes. The clock should then display the updated time.


SkyScan Atomic clock model 86715?

The SkyScan Atomic Clock model 86715 receives radio signals from atomic clocks to stay accurate. It automatically adjusts for Daylight Saving Time and has a large display for easy reading. It also features an alarm with snooze function.


Where can I obtain instructions for the operation of a Atomic clock?

http://www.lacrossetechnology.com/8117it/manual.pdf This has the instructions for your atomic clock.


How do you turn the alarm off on skyscan atomic clock model 38229-1?

To turn off the alarm on the Skyscan atomic clock model 38229-1, press the "ALARM" button until you see the alarm time flash on the display. Then, press the "SET" button to deactivate the alarm. You should see the alarm icon disappear, indicating that the alarm is off. Be sure to check the owner's manual for specific instructions related to your model.


How does alm and snz in skyscan atomic clock?

In the SkyScan atomic clock, the terms "ALM" (almanac) and "SNZ" (signal noise zeroing) relate to the clock's ability to maintain precise timekeeping. The ALM data provides information about the positions of satellites, which is essential for accurate time synchronization via GPS. Meanwhile, SNZ is a technique used to reduce noise in the clock's signal, enhancing stability and precision. Together, these functions ensure that the atomic clock delivers reliable and accurate time measurements.