0
On a 93 Chevy cavalier- do you have to pull steering wheel to replace ignition switch?
Wiki User
∙ 18y ago
yes
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
Do you have to go through the steering column to replace an ignition module?
Are you talking about the electronic ignition module or the ignition switch? The ignition module sits in the engine compartment and is part of the ignition system (coil, spark plugs, etc). The answer is no if this about what you're referring. The answer for the ignition switch will depend on the vehicle you have. Some, like late model Fords, you don't. Push in the retaining pin and the ignition switch comes right out (you still need a key though). Others you need to take off the steering wheel to replace the switch.
How do you replace a starter switch in a 1987 Chrysler LeBaron Town and Country Turbo with a tilt wheel?
There is a solonoid on the starter and the ignition switch is on the steering column.
How do you change an ignition key switch?
you have to remove the steering wheel. (if it has an airbag, be very careful not to set it off.) if no airbag, just remove the steering wheel, and on the ignition switch there is a bolt that simply screws out. remove the ignition switch, and replace with the new one. line up the bolt holes, and replace bolt. put steering wheel back on, and youre done.
Do you need to replace the ignition lock cylinder when you replace the ignition switch on a Pontiac Sunfire 1999?
No, not if it is not defective. If the ignition switch is defective then that is all you need to replace.
How do you replace the ignition switch in a 1987 grand marquis with broken tumbles?
found this, might be the same, Merry Christmas, anyways! :) For a 1988 Mercury Marquis remove bottom shroud from steering column (5 Philips head screws). There is a wire running from the ignition switch to the left side of the steering column; detach it from the coupler (This can be done without a tool). Turn key to ON position until the panel lights come on. There is a small pin near the bottom of the key lock; push it in and pull the ignition switch out (don't panic if the wire seems to be stuck; it will come out). To replace, turn new ignition switch to same position. Push pin on the ignition switch in while sliding it back into the steering column. Reconnect wire and then replace shroud.
How Do You Replace Ignition In 1992 Cavalier?
how do you replace ignition switch on a 1992 Chevy cavalier 2.2 4 cylinder
How do you replace an ignition switch in a 1992 cavalier?
First remove the steering wheel, remove the torx screws and remove the house, remove the signal switch and the wiper switch, remove the torx screws and?æremove the ignition switch. Put in the new switch and replace everything in reverse.?æ
Where is the kill switch on a 1996 cavalier?
The ignition switch, or "killswitch," for a 1996 Chevy Cavalier is located inside the steering column. Replacing or repairing it requires disassembly of the steering column.
Where is the flasher for a 1989 Chevy Cavalier?
It is located by the ignition switch on the right side of the steering column.
How do you get to the ignition switch to replace it on a 1994 Chevy pickup?
Lower the steering column.
How do you change the ignition switch in a 1987 Ford Bronco 2?
Remove the airbag and steering wheel, remove the torx screws from the steering housing and remove the housing, remove the screws from the signal and wiper switch, and remove the screws above the ignition switch and remove the switch. Replace the switch and replace everything in reverse.Ê
How do you replace the ignition in a 1994 Chevy Cavalier?
You'll need a new ignition switch and key provided from your dealer, the bill won't be pretty!
How do you replace the ignition lock cylinder on a 2004 Honda civic?
The ignition lock switch is found under the steering column on a 2004 Honda Civic. Remove the steering column and ignition switch. Loosen the mounting screws that hold the cylinder in place. Pull and replace the lock cylinder.
How do you replace ignition switch on 96 caprice 9c1?
you have to take the bottom steering column apart.
How do you remove the Ignition switch assembly on a 1993 Acura Legend?
you have to replace the whole steering column
How do you install ignition switch 1988 gmc truck?
You need to remove the steering wheel first with a puller. There is a latch you can trip with a small screwdriver that will let the ignition switch slide out. Simply replace the switch and put the steering wheel back on.
How do you remove the ignition switch on a 1999 Chevy Cavalier?
Remove the retaining ring from the top of your 1999 Chevy Cavalier ignition switch. Slide the ignition switch out and remove the wiring harness from the end of it.
