0
On this HK USP 45 full size factory new gun the slide when you try to rack it by hand doesn't rack with an unloaded magazine in the gun?
Wiki User
∙ 15y ago
Take it to a qualified gunsmith.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you remove magazine tube on Stevens 87d?
To remove the magazine tube on the Stevens 87D, first ensure the firearm is unloaded. Then, unscrew the end cap at the front of the magazine tube. Slide off the end cap and follower, then push the magazine spring and follower out through the rear of the tube. Finally, slide the magazine tube out of the receiver.
How do you field strip a RG26 25?
To field strip a RG26 25, ensure the firearm is unloaded, then remove the magazine. Pull the slide back and lock it into place, then depress the button or lever to remove the slide from the frame. Finally, disassemble the recoil spring and barrel for thorough cleaning and maintenance.
How do you lock the m9 service pistol slide to the rear with a magazine inserted?
If the magazine has no cartridges in it, just pull the slide back - the magazine follower will actuate the slide release and lock the slide to the rear. If it's not an empty magazine, you need to push up on the slide release (located on the left side of the frame) while you pull back on the slide.
How do you field strip a model 1911a1 45 acp pistol?
First, MAKE SURE THE GUN IS UNLOADED! Pull the slide to the rear, and lock it. Remove the magazine. Take the spring pressure off the recoil spring, by carefully turning the catch to release the recoil spring cap. Unlock slide, and slide it so that it's over the dismount cutout. Push slide lock out with fingers, and take slide off rails. Barrel will fall out of slide. Reverse to re-assemble.
How to clean a Colt 22 Woodsman pistol?
Make sure gun is unloaded! Lock slide to rear. Remove magazine. Use any commercial gun cleaner(Hoppe's,etc) Use soaked patches to swab barrel inside and out, breech area,magazine well,etc. Wipe down with dry patches
Disassembley for smith and Wesson 909?
Make sure the weapon is unloaded, remove the magazine and then make sure the safety is in the off position. Pull the slide to the rear about 1 inch until the slide stop is below the notch in the slide. Hold the slide in that position and push the slide stop pin from right to left and remove the pin. Let the slide move forward and off the frame. At this point, you have access to the recoil spring and barrel. You can remove the recoil spring, guide rod and barrel at this point.
How do you disassemble a bryco 59 9MM?
Follow the instructions in the owner's manual; find a gun smith. unloaded, uncocked magazine removed, nothing in the chamber, take a pencil or pen and push in the takedown button on the back of the grip. While holding in the button, lift the back end of the slide off of the frame and slide towards the front.
How do you load a glock?
Remove magazine, load cartridges into magazine, replace magazine, operate slide to chamber cartridge.
What are the steps for m9 magazine reassembly?
It should have only been disassembled at operator level. You place the barrel into the slide, place the return spring into the slide, mount the slide onto the frame (pulling back the slide into place), flip the slide release up, then perform your functions check.
How take apart bryco 380?
Place the pistol on safe. Remove magazine, pull back slide and be SURE weapon is unloaded. Push the take-down button located at the rear of the slide using a punch tool. While holding the take-down button in, lift the slide away from the frame, then release the take-down button and pull the slide off the front of the gun. The firing pin and spring can be removed from it's slot in the slide. I strongly advise to go no further.
How are rock slide and mud slide are different?
one has rocks and the other doesnt
How do you reset factory settings nokia 6700 slide?
nokia 6700 slide
