== == Assuming this inquiry is a request for information rather than related to any practical application, here is the answer: It won't work for long. If it was a low-power bulb it would probably just go "pop" and be useless but if it was a high-power bulb it might even explode with a loud "bang", sending broken glass shards in all directions!
So don't try to do it as an experiment because the result could be very dangerous.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
The result is depend on the capacity and the type of the bulb, if the bulb is made of the material which have the high melting point and it have the high resistance then the bulb will light and if the bulb can't afford the voltage means the resistance of is not to much high or the area of the filament is thin then the bulb will light for 1 or 2 sec after that the filament will break and the bulb will not be able to light again.
Assuming it fits you will get about 1/2 the light output if it lights at all. If it is a typical incandescent bulb you'll get some light. If it is some type of specialty bulb it may require the higher voltage or a ballast and may not light at all.
It makes no sense to try to use a 12 volt bulb in a socket that is fed by 120 volts, even if the socket is the right size, because 120 volts is ten times bigger than 12 volts. If you did it, the 12 volt bulb would be totally overloaded by the extra voltage and its filament would immediately be destroyed.
If you mean that the lamp is rated for 240 volts then yes, a 120 volt bulb will operate in it if the lamp bases fit. If the 240 volt lamp is operating on 240 volts then no, a 120 volt lamp will not work in the fixture.
You can use it, the light will not be as bright but the lamp will last much longer. A few years back there was an advertisement for light bulbs that would last years. All they were was bulbs that had a 130 volt rated filament and running at 110 volts they did last for years. The draw back was that they didn't produce the rated wattage that was printed on the bulb.
lamp go "POOF!" It may be very bright, but not for very long!
Without a transformer, the 120v lamp with receive too many volts and it will "blow up" (fuse).
Not only will it work, but it will last for much longer than if it was connected to 220volts!
No. Besides that 240V fixtures may have special base or electronics for a certain type of bulb.
You're looking at 130v light bulbs? Well...the answer is "nowhere." A 130v light bulb has a heavier-duty filament in it than a 120v bulb does, so the bulb will last longer. Put it in a regular socket and it will work fine.
You can't "convert" a 120V receptacle into a 240V receptacle.A proper new 240V branch circuit complete with correctly sized circuit breakers, wiring and socket outlet is required.For more information see the Related Question shown below.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
If all the components are rated to 220V, yes. Keep in mind that if the appliance was designed for 110V it may arc if 220 is run through it. If you don't know the device can handle 220V, don't run it at 220V. Chances are it was manufactured cleaply and cannot handle the extra voltage.
If I understand your question, Can you run a 110 appliance off of a 220 volt outlet? You could by only using one leg of the 220. You may also consider changing the outlet. Put in a regular 110 outlet and capping off one leg of the 220 in the wall box. You still have a neutral and a ground to work with. I read this as the questioner doesn't want to modify the outlet. Check the voltage ratings on the device. Many electronic devices nowadays can havdle 120V or 240V as it is cheaper to manufacture one powersupply and sell it everywhere. If your device is rated for 240V, you can put a 240V plug on it. If it only says 120V, no dice. 240V will burn it up.
If the meter has 208-240V coming to it, no the neutral doesn't go through the meter. If the meter has only 120V incoming power such as many RV parks then the neutral does go to the line side of the meter or it won't work.
Off hand no but your explanations are not clear as to who is doing what to whom,,
You're looking at 130v light bulbs? Well...the answer is "nowhere." A 130v light bulb has a heavier-duty filament in it than a 120v bulb does, so the bulb will last longer. Put it in a regular socket and it will work fine.
NO. Don't try it. Some are designed to work on either, some aren't. If it won't work on 120v, it won't work on 240v.
It will work it you use 240 volt light bulbs.
Actually, I have seen this in a respected electronics magazine (Elektor) quite some time ago: A diode (selected to be capable to handle the amps, the voltage and the heat from the bulb - if placed inside the lighting fixture) is used to "cut off" one half of the AC sine wave and thus sending pulses of 120V to an incandescent light bulb, simulating a simple dimming device. The proposal was meant to run 240V bulbs at 50% of their brightness but I am pretty certain this concept can be used to run 120V bulbs from 240V power. One other way of connecting 120V bulbs to 240V would be to connect two 120V bulbs OF THE SAME WATTAGE in SERIES, so the two bulbs form their own voltage divider. Not sure what happens if one bulb burns out - I would expect the other one to blow too, as a dying light bulb represents zero Ohms (plasma/arcing) for a few milliseconds before it goes dark forever.
It can, but if you're wanting to run a 120v light bulb on DC, you'll need 120v DC to get the rated output. That's a lot of batteries. It's easier, and more sensible, to find a DC rated light bulb, such as an RV bulb.
You can't "convert" a 120V receptacle into a 240V receptacle.A proper new 240V branch circuit complete with correctly sized circuit breakers, wiring and socket outlet is required.For more information see the Related Question shown below.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
The UK uses 240V, so your dryer will probably work, as the US uses 240v in homes for dryers. However, your washer won't as the US uses 120V for washers.
If all the components are rated to 220V, yes. Keep in mind that if the appliance was designed for 110V it may arc if 220 is run through it. If you don't know the device can handle 220V, don't run it at 220V. Chances are it was manufactured cleaply and cannot handle the extra voltage.
No - The us version will NOT work in Bahrain ! You would need a charger suitable for use on the Bahrain electricity system.
Verify that wires to bulb socket are connected and not damaged. Verify that socket is not corroded. Verify that fuse and bulb really are good. Drew
Find out why it is not working. Do you have 12 volts at the bulb socket. If not, then you have a loose or corroded connection. If you have 12 volts then the bulb is blown or not making good contact. The license plate bulb is wired into the taillight circuit and operates on the same fuse. So if your taillights work then the problem is between the taillights and the license plate bulb socket.