K=E/(3*(1-2v))
K: Bulk modulus
E: young modulus
v: poison's ratio
on the other hand:
delta V/V=(1-2v)*delta L/L
relative change in Volume equals to: (1-2v) * relative change in length.
E=2k(1-2v)
E=youngs modulus
k=bulk modulus
v=poission's ratio
p -0.29,e-12.4e3mpa
between .15 and .20
The bulk modulus (K) is a material's resistance to uniform compression from all directions. If you have Young's Modulus (E) and Poisson's ratio (ν), the relationship is: K = E/(3*(1-2ν)) For E = 220 GPa and ν = 0.29, K = 174.603 GPa
Modulus of Compression is the ratio of stress to strain in an uniaxial compression action, while as, bulk modulus is the ratio of volumetric stress (hydrostatic pressure) to volumetric strain in hydrostatic loading. These two modulii are inter-related though and are written with the use of Poisson's ratio. 1/m = (3K-E)/6K 1/m = Poisson ratio K = Bulk Modulus E = Elastic Modulus Satisfied? - tell others, not satisfied? - tell me.
Yes, if the material is very thin in ther axis of compression. If it is not thin, as in compressing a long cyclinder, you do not need to know bulk modulus. If very thin it won't make a lot of difference if it a metal with usual poisson ratio of about 0.25, but will make difference for possion ratio higher, especially approaching 0.5, as in rubber. In the case of the long cyclinder stress = modulus xstrain In the case of the thin material stress = modulus x strain times the quantity (1-u)/ ((1+u)(1-2u)) where u = poisson ratio; the relation to bulk modulus for u is u =1/2 - E/6B where B = bulk modulus and E = elastic modulus
p -0.29,e-12.4e3mpa
between .15 and .20
since k=E/3(1-2n): where k=bulk modulus and n=poision's ratio it can be seen that value of poision's ratio can't be smaller than 0.5 in order to keep k be +ve.hence poision's ratio is 0.5
Young's modulus
Depends on the hardness of the formulation. Poisson's ratio depends mainly on the bulk modulus and slightly on the Youngs modulus at very low strains for the subject compound. If the Youngs modulus lies between 0.92 and 9.40MN/m², Poisson's ratio lies between 0.49930 and 0.49993.
The bulk modulus (K) is a material's resistance to uniform compression from all directions. If you have Young's Modulus (E) and Poisson's ratio (ν), the relationship is: K = E/(3*(1-2ν)) For E = 220 GPa and ν = 0.29, K = 174.603 GPa
Modulus of Compression is the ratio of stress to strain in an uniaxial compression action, while as, bulk modulus is the ratio of volumetric stress (hydrostatic pressure) to volumetric strain in hydrostatic loading. These two modulii are inter-related though and are written with the use of Poisson's ratio. 1/m = (3K-E)/6K 1/m = Poisson ratio K = Bulk Modulus E = Elastic Modulus Satisfied? - tell others, not satisfied? - tell me.
G = E/2(1+u) where G = mod of rigidity and u =poisson ration and E = young modulus
It is around 40 GPa.
Young's modulus-205 kN/mm2 Poisson's ratio = 0.30
It is the ratio of shear stress to shear strain.
Liquids are not defined by elastic modulus, but rather by bulk modulus, which for water is about 2200 MPa (320,000 psi). It is nearly incompressible, with a Poisson ratio close to, but not quite,0.5