how tremove aircon housing unit under the left glove comparmentona polo 1.6
To remove the air box on a 2007 Mazda 6, remove the nuts on the top of the box. Carefully place the nuts aside, and remove the top to access the filter or housing assembly.
How is the plastic air horn attached to the air box? On checking the air filter I found plastic horn laying in the bottom of the air box.
Loosen the hose clamps on each end of the big square air box and remove it. Then you can release the clamps on the air cleaner box, remove the lid, and remove the filter.
drivers side under the air filter box housing under the hood once you remove the air cleaner box its in a sealed black abs box
The cabin air filter is located behind the glove box. If you remove the glove box door you will see a small access door in the HVAC housing.
The thermostat housing is on the driver side of the motor. It is partially covered from above by the intake. If you remove the intake air supply hose from the intake and from the air filter box it should make the housing more visible. This is for the 3.4 engine.
IAT sensor is located on the intake tube of the air filter box, just behind the driver side head light. remove the cover of the air box as if you were going to change the air filter. in the back of the air box are two 10mm bolts holding it to the battery tray. remove thoes bolts and pull up on the air filter lower housing. attached to the housing is a wire with a pinch connector. that unit is your IAT.
The air filter of a 1997 Dodge Neon coupe is located in the air intake of the vehicle. Standard intakes use a plastic housing which flows throughout the engine bay. Locate the housing for the filter and remove the clips from the air box. Open the box and replace the filter.
Remove the obvious bolts and then give her a pull and wiggle. The box sits in rubber brakcets that tend to hold.
Cabin air filter is located behind the glove box. Remove glove box[one screw] and pull filter out of blower housing. New filter will have instructions.
what is an air box
Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed. Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.Locate the air filter intake box on the driver's side of the engine. Remove the intake box by unscrewing the small bolts from the inside of the box with a 3/8-inch drive ratchet, extension and a socket. Pull the intake box off and place it to the side. The thermostat housing on the engine block can now be accessed.