0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you replace a ball joint?
Remove the tire and wheel. Remove the brake assembly and rotor. Remove the retaining nut from the ball joint. Pound the ball joint out with a hammer. Reverse the process to install the new ball joint.
How do you replace the front wheel bearings on a 1994 Saturn and what is the best way to remove it from the controller arm?
Remove u-joint clip (CV Joint), remove as an assembly, press bearing out.
How do you install lower ball joint for 97 dodge neon?
Remove the tire and wheel. Remove the brake assembly and rotor. Remove the ball joint retaining nut. Pound the ball joint out with a hammer. Reverse the process to install the new ball joint.
How do you change a CV joint on a 1987 Honda Civic?
Begin by removing the tire and wheel from your 1987 Honda. Remove the brake assembly and the brake rotor. Remove the CV joint retaining bolts. Reverse the process to install your new CV joint.
How to remove ball joint from 02 chrysler town and country 3.8 van?
Remove wheel followed by the caliper slide pin bolts remove the caliper and suspend it from the strut next remove the ti rod end by hitting the outside of the mount that its in next get a pickle fork and realese the taperd shaft of the ball joint after u remove the bolt holding it into the assembly after that remove the two bolts holding the strut to the assembly and wiggle it loose the take the whole assembly and with a ball joint press that u can rent press the ball joint out u have to buy a whole control arm if u want to replace the upper ball joints but lowers u can press out. Then do everything in reverse
How do you replace universal joint on front axle of a 93 dodge w 250?
This for the 4x4 version, remove the caliper and brake assembly, remove the spindle nut (large bar or very large impact) remove the lower ball joint nut slowly with a jack under the ball joint and gently release the pressure on the suspension eventually lowering the jack. swing the wheel hub assembly a side and remove the axle. place the joint in a supported vise and remove the retainer clips that hold the u-joint stable in the joint housing, gently with a socket the same sixe of the u-joiny cap and a brass hammer pound the joint from the housing, install the new joint and reassembly in the reverse of disassembly. Be sure to torque the spindle not and replace all clips/kotter pins.
How do you replace an universal joint on the right front of a 1984 Chevy full size blazer?
Jack up and support the right front of the vehicle. Remove the wheel/tire. Remove the brake caliper and hang the caliper with a piece of wire out of the way. Remove hub/rotor assembly. Remove backing plate and spindle. Slide out axle assembly. Replace u-joint as you would on a driveshaft. Assemble in reverse order.
How do you replace lower ball joints in 2001 f 150?
To replace ball joints on a 2004 2WD Ranger, lift the upper control arm of the spindle assembly and remove the nut holding the lower ball joint in place. Then lower the lower control arm to relieve the ball joints. Replace with new.Ê
How do you change the lower left ball joint on a 92 chev s10 blazer 4x4?
Remove the tire and wheel from your 1992 Chevrolet S 10 Blazer. Removing the brake assembly and the brake rotor will give you more room to work. Remove the ball joint nut. Pound the ball joint out with a hammer. Reverse the process to install the new ball joint.
How do you change the lower ball joint on a 2001 Ford Ranger edge four wheel drive?
replace lower ball joint on ford ranger 2001
How do you change the front wheel bearings in a 2003 Monte Carlo?
You have to replace the entire hub assembly, the wheel bearings are inside of it. Jack up car, remove tire, remove brake caliper and rotor, remove hub nut on cv axle, remove bottom ball joint nut(use pickle fork tool to remove ball joint from hub), tap cv shaft loose of hub, unbolt strut from hub, unplug abs wire, and replace hub assembly. Reverse steps to reassemble.
How do I remove the U-Joint from the drive shaft after snap rings are removed?
You have to pull the bearing assembly out. Be careful and do not let the cap covering the bearings come off.
