Serpentine Belts
Ford F-250
Chevy Trailblazer

Remove serpentine belt on 2000 Malibu?


Top Answer
User Avatar
Wiki User
Answered 2010-02-19 00:59:54

First you must jack up engine on right side of car. 2nd remove the motor mount bolts. 3rd loosen 15mm nuts on inner fender. Then carefully slide belt through the motor mount.


Your Answer

Related Questions

How do I rethread the serpentine belt on a 2002 Malibu with a V-6?

Remove the serpentine belt and remove the alternator. The belt tensioner bolts are under the alternator.

Begin by loosening the tensioner pulley on your 2000 VW. The serpentine belt will become loose when the tensioner pulley is loose. Remove the old serpentine belt and put the new serpentine belt on. Tighten the new serpentine belt with the tensioner pulley.

You need to remove the serpentine belt and unbolt the old alternator. Bolt on the new one and reinstall the belt. Its that easy.

remove the belt. then in center of the tensioner is a bolt that goes into engine. remove this bolt. then tensioner should come off.

Remove serpentine belt. Remove alternator. The bolts that hold the tensioner on are under the alternator.

You can remove your serpentine belt by loosening the tensioner pulley. Pushed the tensioner pulley to the right and the serpentine belt can be easily removed.

Just a serpentine belt. May have to remove a motor mount in order to change it, that varies by the year.

replacing serpentine belt on 2000 chevy prizm need help

you have to remove the belt tensioner to remove the belt off of the engine.

it could be a serpentine belt or accessory belt.

should have 1 big belt called a serpentine belt.

find tentioner pull counter clockwise. this will relive presure/remove belt. Reinstall

what are the correct steps to remove the serpentine belt that runs to the alternator on a 2001 Toyota AvalonWas that an ANSWER!? I assume the question is, "How do I remove and replace the serpentine belt on a 2001 Toyota Avalon". (You can remove it with a good sharp knife!)

Loosen the tensioner pulley. Slide the tensioner pulley to the right. The serpentine belt will come loose. Remove the serpentine belt. Reverse the process to install the new serpentine belt.

Take pressure off belt tensioner and belt should slide off pulleys

The belt is bad if it has 3 cracks per square inch.

below the alternator. there is a diagram on the engine above the serpentine belt

Raise the hood and look at the belt. If it is broken you will readily see this.

You probably have a bad serpentine belt and tensioner.

It has a serpentine belt and has a self adjusting tensioner.

1. Make sure that when you purchase a new belt, they don't try to sell you the full size serpentine belt. 2. There is a diagram of the belt routing on your truck when you lift the hood. Follow that. 3. Unfortunately, you need to remove the serpentine belt to replace the air conditioning belt.... the belt routing for the serpentine belt is also shown on the diagram. 4. To remove the serpentine belt, get a ratchet set, and crank the "self tensioning" assembly to release tension on the serpentine belt, and remove the belt. 5. There is another "self tensioning" assembly for the air conditioning belt. Crank to place the new AC belt on and release. 6. Re-install the serpentine belt. This is an easy fix... it took me less than 20 minutes, I'm not a mechanic.

i brought my car to mechanic they install the serpentine belt # 950k6 is that the right belt

Remove serpentine belt. Remove pulley. Install new pulley. Install serpentine belt.

Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.