0
I wanna use resistor , capacitor and amplifier 7173 for switch alarm circuit. How can i choice resistor and capacitor value because i wanna use 24V DC.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How a fire alarm would be raised?
The fire alarm device is usually equipped with an Amercium-241 that is alpha emitter source together with a battery derived electric circuit. In the normal situation the alpha particles ionize the air causing circuit connection. However when there is a smoke the circuit is disconnected due to the smoke that acts as an insulator and hence the alarm is actuated.
Will disconnecting the negative battery cable reset the alarm for a 1997 Jeep Grand Cherokee?
if you have a factory alarm..you will need a power remote to reset the alarm. or you can reset the alarm be using the key in any of the door locks or in the rear hatch lock . just cycle the key to the unlock position to shut alarm off. to reset alarm to armed use the door lock power switch to lock the door then shut door and alarm will reset to on .
How Can you permanently disable the security alarm on a 96 vw jetta?
I was just talking to my VW mechanic and he tells me he can disarm my alarm by fusing a connection which is located in the area behind my headlight switch. Tight spot if you have ever been under the dash of your VW. He is going to do it this Saturday. Will give you an update when the job is done.......
Headlights on 1995 jeep grand Cherokee Laredo keeps flashing with engine off what is wrong?
Short circuit in your vehicle alarm system. In most alarms, some lights will flash on and off as an indicator of an attempted break in.
How do I reset Radio Shack alarm?
That depends on the specific model of the alarm.
What is a function of a resistor in a fire alarm circuit?
A resistor in a sensor circuit is used as a simple way to monitor the function of the circuit. The resistor has a calibrated and known voltage drop and current while the circuit is "normal". If there is a short-circuit, or an open-circuit, the voltage and current will change and trigger the trouble alarm.
How do you build a door sensor alarm system using a simple circuit board?
I bought: reed switch LED Buzzer Button (On/Off) Resistor (if necessary) I connected: <---Button------Reed switch------Resistor (if necessary)------LED------Buzzer---Batteries--->
How do you replace the backup alarm sensor?
There's no sensor for the backup alarm. It's either wired to the reverse lamp switch (or corresponding circuit from the transmission ECU if you're running an Allison) or spliced into the reverse lamp circuit. Either the alarm's not getting power, it's not grounded, or the alarm itself is faulty.
What are the applications of silicon controlled switch?
voltage sensor, alarm circuit, Pulse generator, counter, register and timing circuits.
What is a Fire alarm circuit style y?
Style Y is a designation of circuit performance under different states of the circuit. For example: an initiating circuit and a NAC circuit may both be class B, with a panel on one end of the circuit and a resistor on the other. If there is an open on either circuit (the panel doesn't see the EOL), then a trouble is initiated at the panel. However, if there is a short between the two wires on a circuit, the panel will react very differently on the initiating circuit than it will on the NAC. Style Y means that the fire alarm panel will display a trouble on either an open or a short on the NAC circuit, where style 4 means that the Initiating circuit will generate an alarm on the panel in the event of a short, and a trouble in the event of an open.
What is the main function of resistances in fire alarm circuit?
Heat changes the resistance of a circuit. The change is detected by the system, and activates the alarm.
What is thyristors?
A thyristor is a part of a alarm circuit you use it so the alarm stays on
Does a fire alarm circuit have to be in a separate conduit?
yes because of it having a signals, if it mix with power cable, fire alarm circuit get distributed.
Why to use pnp transistor in fire alarm circuit?
You can use a PNP or an NPN transistor in a fire alarm circuit. Both will work. It all depends on how you want to energize the alarm, and with what polarity of signal.
Alarm circuit for the train in same track?
no
Why would the car horn keep honking without pressing the horn?
if its not the alarm malfunctioning, there is a short circuit somewhere between the switch/battery/relay and the horn its self - youll have to find the short and insulate the wire or replace the switch.
How do you disarm the door warning alarm in a 1994 940 Volvo?
Remove the switch and disconnect the wires. Then solder the wires together (making a note of polarity if there are more than 2) to create a circuit. This will then act as though the door is shut and the alarm will not sound.
