0
Should a top load washing machine drum wobble back and forth at rest?
Wiki User
∙ 11y ago
This is normal for most washing machine designs. The reason is to enable access to spring attachments which allow the barrel/drum to move during cycles when machine is operating. If there was no 'wobble' the building housing your laundry machines would shake apart with the centrifugal forces created.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Does a washing machine need a magnet to operate?
The answer is both yes and no.It actually depends on the kind of washing machine in question.The problem is the motion.A washing machine need some kind of an engine or motor in order to move the cloths back and forth. This can of course be done manually.If we rule out manual washing machines, and also only count in electrical ones then these can be made in two different ways.The motor causing the tumbling or the motion in the washing machine can be made with both permanent magnets like NeoDym, or with purely electrical pulses creating strong electromagnetic fields.Most motors in washing machines made today are made without magnets. It is cheaper to make purely electrical motors where the electricity provides the magnetic fields needed. By electronically rotate the magnetic field around the axis, this will force the motion of the motor. It would use less electricity to make the motors with NeoDym magnets but it would also cost more to produce.As a conclusion: We can not make an electrical washing machine that operate without magnetic fields, but magnetic fields does not have to be made by magnets.
How does the agitator work on a washing machine?
the agitator on most washers go back and forth . at least one i know of goes up and down. we will talk about the back and forth.Underneath the tub usually accessable from the back of the machineis a transmission and belt along with other things. when you start the washer it will fill with water . When the correct volume of water is reached a switch is activated that sends power to the timer which in turn routes power to the proper connections needed to agitate. now when washing power is sent to a agitator control which lifts a plunger that makes the transmission rock back and forth which is calledagitation
Why does the washing machine make a loud banging noise whenever washing towels?
The banging noise you hear is caused by the tub&drum banging on the metal case of the machine. The Plastic Tub which holds the metal drum inside has a concrete block on top of it and is held up (like a swing) by suspension (most often by springs). In a wash cycle, it is perfectly normal for the tub to swing from side to side, back and forth. In your case the swinging is excessive Things you can fix: -Machine is leaning to one side (balance the feet) -unbalanced load (dont underload it, make sure heavier items are not put in on their own ect. This can be determined by seeing if your load sticks to one side of the drum when it spins) Things a proffessional can fix: -loose suspension -loose concrete weight -loose cables/pipes hitting the casing -loose drum -calibrating the elctronic speed controller (that makes sure banging doesnt happen by setting suitable speeds) Make sure you open your machine (usually from the top) and have a look inside, explore and understand. Run the machine with the top off, so you can see what is causing the noise. It is safe to do so. (Try to use any tool you have against a star bolt/screw) Thanks for reading Good luck Mr Yasser
The working principle of a washing machine is?
A washing machine is a popular electronic home appliance, which is found in almost every household. In this fast age, a washing machine is highly popular because of its great utilities. It does the laundry quite fast, saving a lot of time and labor. It manages to do so, quite effectively and efficiently, as it follows a set wash process. A brief overview of how a washing machine works with respect to its different parts, is mentioned below.Basic Structure: The elementary components of a washing machine are agitator, inner and outer wash tub, electric motor and drain tube. A washing machine is also equipped with the valves, switches and timers to smoothen its working. Valves enable the passage of hot and cold water to the washing machine. The timer enables timed functioning. A typical washer has switches to adjust and control various functions. The speed of spinning, the special settings for different fabrics and the passage of hot and cold water are the functions monitored by the switches. Valves, switches and timers differ from model to model.These components have to be present in any type of washing machine, be it top-loading or front-loading. Different models of washers differ only in the positioning of these parts. There is a specific function assigned to each part.Inner Wash Tub: The process of washing starts in the inner wash tub. It involves the adding of water and detergent mixture to the clothes. The detergent contains many enzymes that work on clothes to clean them. Some such enzymes are protease, lipase, catalase and amylase. In the inner wash tub, the clothes are tumbled and moved to all sides by the agitator.Agitator: Agitator enhances the action of enzymes on clothes. An agitator is a plastic cylinder positioned at the center of the inner tub. Generally, an agitator is finned. Its finned structure aids it in its function. The function of an agitator is to move the clothing up, down, back and forth so that the clothing mixes well with the detergent. The inner wash tub also moves along with the agitator. This motion is repeated for a determined period of time. The agitator ensures thorough cleaning of the clothing. This cycle is known as the wash cycle. The inner tub has numerous holes. The centrifugal force pulls out wash water from the clothes and makes it move through these holes to the outer tub. The water gets drained out through the drain tube.Motor: In the wash cycle, the agitator and the inner tub are moved rhythmically by a powerful electric motor. In fact, it is the motor which accelerates the process of washing. Therefore, it is a very important component of a washer.Outer Wash Tub: The outer wash tub is stationary. Water gets pumped out from here. After the wash water has left, the inner tub is again filled with clean water. Agitator again works to tumble the clothing. This is the second cycle and is called the rinse cycle. The aim of this cycle is to discharge the detergent particles trapped in the washed fabric. On completion of rinsing, the machine again drains out water.Drain Tube: The purpose of the third cycle, which is called the spin cycle, is to remove out as much water as possible from the wet clothes. In all the steps, draining is carried out by the drain tubes. Once the water has been drained out, another electric motor comes to play. It agitates the inner tub at an extremely high speed. The centripetal force spins out remaining water from the fabric and expels it through the drain tube. This is a timed process. The clothing get reduced from saturated to merely wet. The cleaning of the fabric is done and it is ready to dry.Power Parts: Electric motors can reach high speeds quickly. In order to smoothen the start-up effects, washers are provided with a clutch. This clutch is similar to car clutches as it has the same standard drum-and-pad construction and functioning. Some units use a simpler method. They make use of drive belts. The drive belts slip on a pulley and fix gradually.
What is a bus that runs back and forth?
a bus that runs back and forth is a shuttle.hi i love you
Should a top load washing machine agitator wobble back and forth when you touch it?
Are you speaking of the drum wobbling or the whole machine? If the drum, when the drum is spinning or when off and stopped? If when the drum is spinning, it wobbles somewhat especially if unbalanced (laundry only on one side). If the whole machine, there are leveling feet on the botton of the washing machine. The height adjustment is made by turning each foot which are threaded into the base frame. Many floors are sloped, this is why the machine has to be leveled first.
What it agitation?
Moving back and forth like a washing machine
How do you fix wobble in a bicycle chain wheel?
First you need to determine if the wobble is from the chainwheel or from the bottom bracket. Then there are different procedures depending on if it's a sideways wobble or a bac/forth, up/down wobble. A sideways wobble can be adressed by bending the chainwheel back into plane using two wrenches/vise grips. One is used for bending, the other as a brace to stop the bend from going too far. a back/forth wobble can be fixed by undoing the chain ring bolts a little, and then, with a piece of wood, knock the chainring back into position before doing the bolts back up again.
2000 Dodge Intrepid 2.7 liter is the harmonic balancer suppose to wobble back and forth towards the radiator?
yes when its broken!
What might cause a smaller car to wobble back and forth and slow speeds?
Bad tire, bad wheel, bad cv shaft.......
Why does my rear wheel wobble back and forth down the road?
because maybe your really fat go on a diet PLEASE!!!!!!!!!! especaly if your rear is wobbaling
Does a washing machine need a magnet to operate?
The answer is both yes and no.It actually depends on the kind of washing machine in question.The problem is the motion.A washing machine need some kind of an engine or motor in order to move the cloths back and forth. This can of course be done manually.If we rule out manual washing machines, and also only count in electrical ones then these can be made in two different ways.The motor causing the tumbling or the motion in the washing machine can be made with both permanent magnets like NeoDym, or with purely electrical pulses creating strong electromagnetic fields.Most motors in washing machines made today are made without magnets. It is cheaper to make purely electrical motors where the electricity provides the magnetic fields needed. By electronically rotate the magnetic field around the axis, this will force the motion of the motor. It would use less electricity to make the motors with NeoDym magnets but it would also cost more to produce.As a conclusion: We can not make an electrical washing machine that operate without magnetic fields, but magnetic fields does not have to be made by magnets.
How is a washing machine a computer system?
A computer within a washing machine controls many aspects: The user interface, that is, buttons, LEDs, display, buzzer, are all driven and managed by a computer. The washing program is controlled by a computer: when to heat the water and how much, when and how to spin, etc. Modern washing machines measure the cleanness of the washing and optimize the washing cycle's duration to wash as long as necessary while completing as soon as possible. Modern washing machines also feature sophisticated spinning and load-balancing algorithms which reduce vibrations during the spinning, thus reducing noise and mechanical stress. A washing machine's computer will also monitor safety equipment: for example, a frontloader's door must be securely locked before water is allowed in. Water flow must be confirmed, and the required amount of water must be in the machine before the heating is allowed on, etc. The washing machine's computer will also monitor the machine's general state of health and maintenance. For example, after a set number of hours of active usage, the machine might display a recommendation to replace the drive belt, or to clean the fluff filter.
What is weave and wobble on a motorcycle?
Weave refers to the forces that make the tail end of a bike to wiggle back and forth while moving, pivoting on the axis that is the handlebars. When the front wiggles, it is known as wobble. These effects will usually become bigger as speed increases, and riding becomes exponentially more dangerous.
How does the agitator work on a washing machine?
the agitator on most washers go back and forth . at least one i know of goes up and down. we will talk about the back and forth.Underneath the tub usually accessable from the back of the machineis a transmission and belt along with other things. when you start the washer it will fill with water . When the correct volume of water is reached a switch is activated that sends power to the timer which in turn routes power to the proper connections needed to agitate. now when washing power is sent to a agitator control which lifts a plunger that makes the transmission rock back and forth which is calledagitation
In the ds game fossil fighters what do you do after you build a time machine?
You get to go back and forth in time I guess
What do motors do in circuits?
Changes electrical energy into mechanical energy.
