0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How does a hydraulic robot arm work?
In order for a Hydraulic robot arm to work, it has to be connected to a tube. The ends of the tube have to be connected to syringes (without the needle). One syringe is pushed in, while the other one is pulled out. As you push one syringe in, the other pushes out, which causes the arm to move.
What is the difference between hydrolics and pneumatic?
Hydraulic cylinders will be linked to the bath at both ends, as the oil needs to remain pressurised to work effectively.Pneumatic cylinders have springs if they're single way cylinders, as generally they can't rely on gravity to revert back to the first stage - dual cylinders on the other hand have 2 springs so they can switch sides.That aside, the hissing from Pneumatics should just about give it away.
What is the difference between contra flow and parallel flow?
These terms are usually used in conjuction with fluid-fluid heat exchangers. In both cases, the two fluids in the exchanger are moving in parallel flowpaths with each other. In contraflow, the fluids move in opposite directions along those paths, so the two inlets are on opposite ends of the exchanger. In parallel flow, the fluids move in the same direction, so the inlets are on the same end.
Why use the dog-bone in tensile testing?
The thinner section of the dogbone will break before the thicker parts at the end. Both ends are held by grippers so the last place you want the specimen to break is at the ends.
What is the advantage and disadvantages of fixed beams?
There isn't really an advantage of having a fixed beam vs. a simply supported beam, it depends on what application the beam is for. If one of the design criteria of the beam is that it be able to deflect from one end to another then you are going to want to use a fixed beam. For example such applications could include a diving bored. A simply supported beam differs from a fixed beam because the beam is supported at both ends. Thus when a simply supported beam is loaded, the deflection will occur throughout the beam, since the ends are confined and will remain as they were. Furthermore on a fixed beam, (the end that is fixed) will have restrictive forces and moments keeping the end from moving.
How do you change fluid in hydraulic clutch on 1995 Ford Contour?
A "hydraulic clutch" use's standard DOT 3 Brake Fluid nothing more. Follow the steel line from the master cylinder up, where it ends is the Fluid Reservoir. Use caution when replacing the fluid as you do not want air in the lines. So to change the fluid simply remove the fluid using an old Turkey baster and pour in the new fluid to the correct level.
How do you repace the lower hose going from the hydraulic pump to the folding top cylinder lift on your 1967 mustang convertible top and do you have to bleed the pump?
You simply unscrew it at both ends. Be sure and put some rags or something underneath because a fair amount of hydraulic fluid will come out when you disconnect the line. The system will bleed itself by running the top up and down a couple of times. You'll have to top off the fluid, though. Be sure to check the fluid level with the top up.
Should you get fire from both ends of solenoid?
no
How do you make a simple hydraulic?
Take a tube, put a piston in it, seal off both ends of the tube, and use a liquid, or gas to put pressure in and remove pressure from the tube. As the fluid or gas goes in the tube, the pressure pushes the piston out. As the pressure is released, the piston can recede.
Should you connect both ends of a battery to a circuit?
ertyui
Should you connect both ends to a battery?
Not if it's explosive ?!?
How do you remove the hydraulic fluid from the convertible assembly in a 1994 LeBaron GTC so as to put the top down manually?
Unhook the hydraulic lines use something to catch the fluid from the ends of the lines. Then push the top down slowly do not rehook the lines or it will not work. The motor can be romoved if you want to. The motor is behind the back seat under the well cover. The top will be manual after following the steps above. Hope this helps you.
The resilent substance that keeps bone ends from crushing when compressed?
The articular cartilage is the resilient substance that prevents bone ends from crushing when compressed. Cartilage is both flexible and tough.
What type of threads does a bit sub have on both ends?
both ends
Should you connect both ends of a battery in a circuit?
it is necessary to connect both the terminals of a battery to a circuit for current to flow through it..!!
What do you call the oily fluid at the ends of the bone?
synovial fluid is present.it lubricates the articular surface
When was Both Ends Burning created?
Both Ends Burning was created in 1975-12.
