answersLogoWhite
Headlights Tail and Brake Lights
Windshields and Wipers
Ford Expedition Eddie Bauer

The rear windshield wiper and running board lights are not working what could cause this?

717273

Top Answer
User Avatar
Wiki User
Answered
2006-09-01 05:13:13
2006-09-01 05:13:13

the fuse that controls the interior lights, running board,an rear wiper is blown. it is a 15amp fuse in the panel. Also,try the cluster dimmer position since it controls the running board lights and exterior mirror lights as well.This dimmer is located next to the headlight switch.Good luck!

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Where is the 1994 JEEP grand cherokee Daytime Running Lamps Lights Module? Lights are working but the running lights and dash board lights are out.


why is my dash board lights not working


I am not a mechanic, however as an electrician it sounds like the running board lights are wired to the same relay as the interior lights. To check this, simply crank the truck, leave all the exterior lights off, turn on the interior light, then walk around the truck and look at the running board lights. If they are on then turn the interior light off and the parking lights on, check to see if the running board lights come back on. Depending on the make and model of the truck, I could be way off in left field and this info may not apply. uuummmm.....programing?



There are several things that can cause your 2000 Cadillac dashboard lights to quit working. The most common cause is a blown fuse.




Check your fuses again-use test light. Almost always seems to be a fuse when both tail lights and dash lights aren't working at same time. If that fails, check headlight switch



run a wire from battery positive to an inline fuse, then to a switch that you have to install in your dash. from the switch to the lights, then to ground. turn on switch, lights should work.


Yes, your tail lights will go out when your dash board lights go out.



If this is an electronic unit, the heat generated after the lights are on for one half hour, is affecting the intergrity of the electronic circuit board.


You get under the running boards right under the lights. there is a little plastic housing. pull this housing down and change light bulb is that easy.


Need to know what about the dash board lights.


They should come on automatically when the vehicle is in operation. If they're not, you might have an electrical problem. If your vehicle is a U.S. vehicle and you want daytime running lights, you must purchase a daytime running lights (drl) module for about $50. and place it in the fuse area off the driver's side dash. Remove the hi beam module and then find someone with a Jeep/Chrysler computer that can flash your computer board and change the country code to Canada and voila, you will have daytime running lights.


under the hood on the driver side there is a fuse box at the very rear if u don't look hard u will miss it cause it is small but u will see one fuse box there but look a little further back to see the other fuse box


How do you change dash board lights on a 1995 Mercury Tracer.


old short guys like me find it easier to get in and out when there is a running board step


Where is the Dash board lights fuse of ford mondeo 2002 lx


Because running an EC, you are the head of the EC so no one can pay you and boarding your horse is to easy xD


You will have to determine if the fuse, the switch, the wiper motor, the linkage, the pulse board or the wiring/connections is at fault before you can fix it.




I had the same problem on my 1998 Ford Expedition XLT. Spray some WD-40, in all the door jams including the hatch / back door. This should take care of problem.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.