Best Answer

check your fuses

User Avatar

Wiki User

โˆ™ 2005-10-07 03:40:29
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: Why are your dash board lights and interior lights not working on your 93 Ford Taurus?
Write your answer...

Related Questions

The rear windshield wiper and running board lights are not working what could cause this?

the fuse that controls the interior lights, running board,an rear wiper is blown. it is a 15amp fuse in the panel. Also,try the cluster dimmer position since it controls the running board lights and exterior mirror lights as well.This dimmer is located next to the headlight switch.Good luck!

How do you turn interior lights offon on cadillac dts 2006?

on the left side of dash board there is a little buttom push it in it will pop out turn it to either brighten dim on turn on interior lights

What would make running board lights turn on when the door is opened and the key is put in the ignition but turn off once the truck is cranked?

I am not a mechanic, however as an electrician it sounds like the running board lights are wired to the same relay as the interior lights. To check this, simply crank the truck, leave all the exterior lights off, turn on the interior light, then walk around the truck and look at the running board lights. If they are on then turn the interior light off and the parking lights on, check to see if the running board lights come back on. Depending on the make and model of the truck, I could be way off in left field and this info may not apply. uuummmm.....programing?

Where does the dimmer module located on a Nissan bluebird?

why is my dash board lights not working

2000 Cadillac dts Dash board lights not working?

There are several things that can cause your 2000 Cadillac dashboard lights to quit working. The most common cause is a blown fuse.

My dash board lights and tail lights are not working and my service engine light comes on. How are these connected and how can I fix the tail lights so they are working so I can pass inspection in NJ?

check the fuse and the park lamp relay

Tail lights and dash board lights not working on 96 Jeep Cherokee classic?

Check your fuses again-use test light. Almost always seems to be a fuse when both tail lights and dash lights aren't working at same time. If that fails, check headlight switch

What could be the reason for dash board lights and tail lights not working on a 1989 Mercury Sable even after the fuses have been replaced?

Is there a penny stuck in the lighter port?

Where is the Daytime Running Light Module specifically located for a 1994 Jeep Grand Cherokee?

Where is the 1994 JEEP grand cherokee Daytime Running Lamps Lights Module? Lights are working but the running lights and dash board lights are out.

2000 impala interior lights not working how do you change the fuse?

open fuse panel on passenger side of dash board fuse is 5 down on left side should be marked TRK/ROOF BRP Pull gentley and replace with one of the same

Do ur tail lights go out when ur dash board lights go out?

Yes, your tail lights will go out when your dash board lights go out.

Why would your speedometer stop working after 30 miles with lights on but not when off?

If this is an electronic unit, the heat generated after the lights are on for one half hour, is affecting the intergrity of the electronic circuit board.

2002 Ford Explorer Eddie Bauer dash board lights?

Need to know what about the dash board lights.

How do you change the dash board lights on a 1995 Mercury Tracer?

How do you change dash board lights on a 1995 Mercury Tracer.

Where is the Dash board lights fuse of Ford Mondeo 2001?

Where is the Dash board lights fuse of ford mondeo 2002 lx

What do the various symbols mean on the dashboard of a 2001 Bluebird Bus?

If you mean the dash board (speedometer, gas guage etc) and not the control board ( it has all the heater, interior lights and so on). The dash board was provided by the company that built the chassis. International, Spartan, Sterling etc. Thats who you need to ask.

Where is fuse box located on a ford 2001 Taurus?

My brake lights, dome lights and dash board lights went out at the same time. I checked the fuse under the hood of the car and I can't locate the fuse box inside the car. My questions are (1) what cloud have cause for all three(3) lights to go out at the same time and (2) where inside the car is the fuse box?

If the highmount brake light is working but the brake lights are not working what is wrong?

It is the brake light switch. The 3rd light has a different switch. GoodluckJoe you can check under neith the bed for fire where they come together. if ther is fire it is the circuit board where your lights go. if there is no fire then its gonna be in the turn signal switch

How do you replace dash lights on 99 Honda accord?

replacing dash board lights

Why don't my tail lights and dash board lights go on in my 1992 Bonneville se?

You may have a burnt out bulb that is causing your tail lights and dash board lights to not come on in your 1992 Bonneville. It can also be a blown fuse that is causing your problem.

What can you do with a light board?

For example, if you are operating a light board in an auditorium, it can control all the lights like flashing, regular, and even stroke lights. I can do every lighting you can think of. All you have to do is set the timer of the lights on the light board and organize each button to operate each light.

The song on your PC is not working and you do not have your mother board CD what can you do to get it working?

If your issue is all sounds not working then, check with the website for the manufacturer of your mother board, for drivers/updates.

What would cause rear parking lights fog lights and instrument lights to not work?

Blown fuse? Damaged buss board?

Where can you illustrations of the dash board warning lights?


Interior lights and running board lights stay on 1999 expedition?

Probably one of your door switches. These are the little nipple looking buttons that tell the truck when to turn on the lights (when you open the doors). You should be able to push it shut with your finger and see if there is still voltage going through the switch to tell which one is bad. There is no real short cut for this.