0
There is a wheel at the top of the serpentine belt that you cant seem to get the belt over you have the belt assembled but you cant get pat this part HELP?
Wiki User
∙ 15y ago
you need to loosen the tensioner.. ist like a small wheel with some sort of spring attatched..
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you put on a serpentine belt on 2001 dodge stratus es?
remove the right front wheel and fender liner to access the serpentine belt and tensioner. Belt routing should be under the hood.
Diagram of serpentine belt 2000 Chevy Prizm?
replacing serpentine belt on 2000 chevy prizm need help
How do you change a serpentine belt on a 1992 Chevrolet G20 van?
This is an easy one. There is a belt tensioner on the top of the engine which applies tension to the serpentine belt. A small wheel rides above the belt and applies the tension. Put a ratchet and socket on the bolt found in the center of the small wheel. The wheel and arm it is attached to will move up as you apply pressure to the ratchet. It is only necessary to move the small wheel and arm a short distance in order to slip the serpentine belt from under it.The trick will be replacing the belt. If the label showing the routing of the serpentine belt is missing (usually on the air intake pipe) draw a diagram before removing the belt.
How do you replace serpentine belt on 91 Chevy G20 van?
This is an easy one. There is a belt tensioner on the How_do_you_change_a_serpentine_belt_on_a_1992_Chevrolet_G20_vanof the engine which applies tension to the serpentine belt. A small wheel rides above the belt and applies the tension. Put a ratchet and socket on the bolt found in the center of the small wheel. The wheel and arm it is attached to will move up as you apply pressure to the ratchet. It is only necessary to move the small wheel and arm a short distance in order to slip the serpentine belt from under it.The trick will be replacing the belt. If the label showing the routing of the serpentine belt is missing (usually on the air intake pipe) draw a diagram before removing the belt.
What is the stationary wheel in the serpentine belt for a 2000 Chevy s10 called?
It is a idler pulley.
Is an accessory belt a serpentine belt?
No, an accessory belt is not considered a serpentine belt. However, a serpentine belt is considered a specific type of accessory belt.
How do you replace a serpentine belt on a 2003 Hyundai Sonata 6 cylinder front wheel drive with AC?
My serpentine belt slipped off. I have a 2003 Hyundai sonata. I need instructions on how to put it back on.
How do you replace serpentine belt on 1995 tercel?
i have a 99 tercel, help?
What could it be if the car started off making a rattling noise and now squeals like a belt is going?
Bad belt tensioner idler wheel, and serpentine belt.
How do you change the drive belt in a 1999 dodge ram 1500?
On the 5.2, there should be a serpentine belt on it. There is a belt tensioner on the passenger side. It is a small wheel with a 15mm bolt on it. Put a wrench or socket on it and turn it clockwise. It should release the tension on the belt. You may have to help it off though.
How do you change the serpentine belt on a 2003 Pontiac Bonneville?
To change the serpentine belt on a 2003 Pontiac Bonneville, loosen the tensioner pulley and remove the old belt. The tensioner pulley is the wheel in the belt system that has a bolt through the middle in a slot that can be adjusted. Put the new belt on and tighten up the pulley.
How do you change the serpentine belt in a 1998 Plymouth Grand Voyager 3.3?
You need a special tool called a Serpentine Belt Tool. In Sears it’s the KD Tools Geared Serpentine Belt Tool Sears item #00947098000 Mfr. model #3680. The key to replacing the belt is pulling down the tension wheel enough so that you can lift the belt around it. The problem with standard tools is that there’s no room to angle a conventional tool in. When assembled the belt tool forms an angle that is just right for the job. Also, when you’re ready to remount the belt feed the belt around all the wheels except the idler pulley. Pull down the tension wheel belt tool and slide the belt over the idler pulley and you’re done. Then keep the belt tool the back of your van because every time you hit a puddle you will have to do the whole thing over again. – Mike Snodderly, USAF retired
