{| ! valign="bottom" | Item ! valign="bottom" | Part Number ! valign="bottom" | Description | 1 6M250 Timing Chain/Belt Idler, Upper 2 6256 Camshaft Sprocket, Front 3 6M250 Timing Chain/Belt Idler, Lower 4 6306 Crankshaft Sprocket 5 6K254 Timing Chain/Belt Tensioner 6 6256 Camshaft Sprocket, Rear Removal # Remove the Engine Front Covers (6019). Refer to the procedure in this section. # Remove the three nuts and the engine support insulator through bolt from the engine support insulator. Remove the front engine support bracket (6028). # Raise and support the vehicle. # Align the crankshaft sprocket (6306) to TDC by turning the crankshaft (6303) in the direction of normal engine (6007) rotation. # NOTE: Remove the lower timing chain tensioner arm bolt before the upper timing chain tensioner arm bolt. Remove two bolts from the timing chain tensioner arm (6285) in the order shown. Remove the timing chain tensioner arm. # Mark the direction of rotation on the timing chain/belt (6268) to be sure of proper installation. # Loosen the timing chain/belt tensioner bolt. # Remove the timing chain/belt. Installation # Compress the timing chain tensioner arm until the hole in the piston is aligned with the second hole in the case. Insert a 1.6mm (0.06 inch) diameter wire or pin through the second hole to keep the piston compressed. # Align the camshafts (6250) to top dead center (TDC). # Turn the crankshaft clockwise until the crankshaft sprocket is offset from TDC by one tooth. # Install the timing chain/belt.
Turn the crankshaft in the direction of normal engine rotation without moving the camshafts, until the crankshaft timing mark is again at TDC. This will place all of the belt slack in the timing chain tensioner arm portion of the timing chain/belt. # Install the timing chain tensioner arm and both bolts. Tighten the timing chain tensioner arm bolts to 19-25 Nm (14-18 lb-ft). # Remove the pin from the timing chain tensioner arm. # NOTE: When correctly timed, the crankshaft timing mark will line up and will NOT be one tooth off. Turn the crankshaft two complete revolutions, in the direction of normal engine rotation, to make sure that the timing is still correct. # Tighten the timing chain/belt tensioner bolt to 35-51 Nm (26-37 lb-ft). # Install the RH engine support insulator. Tighten the three nuts to 74-103 Nm (54-76 lb-ft) and the RH engine support insulator through bolt to 67-93 Nm (50-68 lb-ft). # Install the Engine Front Covers . |}
where are timing marks on 89 ford probe 4 cylinder I have the bottom not the top
They are on the camshaft and crankshaft sprockets
To set the ignition timing on a Ford Probe GT 95 with an MX engine, remove the two 12 mm head bolts holding the distributor in place. Then rotate the distributor to set the ignition timing.
It is right about $50.00. At least, that is what the local Autozone sells them for.
Replace the chain and both the cam and crankshaft gears.
motorcraft.com shows for the 1990 Ford Probe 2.2 L ( 133 cubic inch ) 4 cylinder : ignition timing : 6 degrees BTDC , and --------------------------------------------------------------------------------------------------------- 9 degrees BTDC - manual transmission - with turbo - with self test connector grounded
Yes, the 2.0 liter 4 cylinder engine in a 1996 Ford Probe is an interference engine ( according to the Gates website , they make timing belts etc. )
No , according to the Gates website ( they make timing belts etcetera ) the 2.0 liter four cylinder engine in a 1997 Ford Probe ( IS AN INTERFERENCE ENGINE )
Ford Probe was created in 1989.
more than likely the tensioner
Yes , according to the Gates website the 2.0 liter 4 cylinder in a 1996 Ford Probe IS an interference engine
yes....