0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How can you hook sub woofer in your pioneer vsx 5900s and these unit 5.1design?
I Have a old Pioneer VSX-5900S hooked to my old Veldyne 806 which is a 8 inch sub and it sounds amazing. If you look on the back you will find the pre amp out and power amp in for the front speakers theres also one for the center and rear speakers if you have two subs and are using it for home theater! Connect the pre amp out to the line level in on the sub and the power amp in to the line level out from the sub. Best of luck! I highly recommend a velodyne sub!!
What is a good sub woofer amplifier?
Depending on the RMS power of your sub, and size and brand of your sub, it will depend. If you have a single sub, I'd recommend a monoblock amp that puts out close to or enough to power your sub. You could also use a 2 channel bridgeable amp, as they are generally a much cheaper option. For dual subs, I'd say a bridgeable 4 channel amp, or high-output 2ch amp. To give an exact amp, I don't go past the Pioneer GM-d8500M 1200w Class-D Monoblock amp.
Is it ok to use a mono amp with a 4-ohm single voice coil sub - The amp is a Pioneer GM-7300M and the sub is an 12 Apline Type e - And what issues may I run into?
Yes you can definatly use these two together. The rms on the sub is 250 and the amp puts out 250 continuous power (RMS) at 4 ohms so yeh this setup should work no problem :)
If i brought 2x400 6x9 speakers from ground zero what power amp and sub would you recommend?
Ground zero should be able to advise you on a power amp and sub.
What will happen if you hook up a system and the amp rms is lower than the sub rms?
you could possibly kill your amp. because the subs are asking for a certain amount of power and your amp cant give the power. but typically the amp will push all its power avalible to the sub and you should be fine. but for the optimum sound system the amp rms should be the same or close to the sub rms.
Can a use jbl gto 3501 amp for two pioneer 1000 watts woofers?
this monoblock amp is bridged internally. It can handle a minimum of 350w RMS one channel and a maximum of 700. I'd suggest letting a mono amp power a single sub for best results. But people do use it to power 2 10 inch subs as well.
When you unplug the rear speakers in a car from your 4 channel amp and just power your sub will all the power from the amp go directly to the sub?
depends on the wiring check out Subwoofer Wiring Diagrams
What type of amp can i use to power 3 12'' sub woofers?
You need to know how much power the sub woofers are rated to handle. Choose a power amp that can supply sufficient power.A power amp designed specifically for sub woofer use delivers all of it's power at the lower frequencies where a sub woofer operates. They may also have better cooling since they operate at higher power than full range amps.
Can you hook a 600watt auto amp to a 1200watt auto sub?
You can, but the Sub will not put out its full sound power.
What watt amplifier will power a 15 inch sub-woofer?
Any amp will power a 15" sub. What you need to know is what is the RMS of the 15" sub. Lets say its 200 watts RMS than you will want a max of 200 watts for your amp.
How can you wire 2 12inch pioneer subs dvc 4ohms 1000 watts max to 2 pioneer 760 watt amps both amps are 2 channel they can be bridged?
You do pos to one side to pos the other side on the sub then the same for negative then to the amp you hook the pos to one channel then the negative to the other channel and the same on the other sub and amp
Why doesnt the sub come when the amp has power?
Sounds like a blown subwoofer.
