0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Which phase change occurs during sublimation?
solid - gas
Do crates made from plywood have to be stamped by IPPC?
The IPPC standard only impacts packaging using solid wood (both coniferous and non-coniferous). Engineered wood products such as corrugated, plywood, OSB, etc. are exempt. If there is any solid wood used in the packaging, the unit must be marked accordingly.
What are cbn grinding wheels made of?
The wheels are generally made from a matrix of coarse particles pressed and bonded together to form a solid, circular shape. Various profiles and cross sections are available depending on the intended usage for the wheel. They may also be made from a solid steel or aluminium disc with particles bonded to the surface.
What are three types of metal transfer in an arc welding process?
Spray, Solid, and Globular which is part way between the other two.
What is pin configuration of IC CD4017?
What is pin configuration of IC CD4017?Pin numberNamePurpose16The 6th sequential output22The 2nd sequential output31The 1st sequential output43The 3rd sequential output57The 7th sequential output68The 8th sequential output74The 4th sequential output80V, VDDThe connection to the 0V rail99The 9th sequential output105The 5th sequential output1110The 10th sequential output12COCarry out output - outputs high on counts 0 to 4, outputs low on counts 5 to 9 (thus a transition from low to high occurs when counting from 9 back to 0)13LELatch enable - latches on the current output when high (i.e. the chip counts when LE is low)14CLKClock in15RSTReset - sets output 1 high and outputs 2 through 10 low, when taken high16+9V, VCCThe connection to the +VCC rail (voltage between +3V and +15V)
What are pin terminals?
Terminals (connectors) which work by inserting pins into holes.
Would you wear a solid tie with a pin stripe shirt?
A solid tie would stand out over a pin stripe shirt.
Why there is a slit in a three pin plug?
If it has a slit in the side of the pin, it is because it was made from flat material that is rolled into a pin. If it were solid. there would be no slit or seam.
What connector or connectors are used with Speaker Cable?
Speaker cable can be used bare or with pin, banana, spade or ring terminals.
2001 Buick lesabre front caliper mounting bolts which one goes top or bottom there is a difference in them?
The top (or leading) pin bolt uses the plastic bushing, the bottom bolt should be solid. Here is a snipet from a manual.Install the caliper over the rotor and onto the caliper bracket. Ensure that the caliper pin boots are not pinched. NOTE: The leading caliper pin, or top pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design.Install the new caliper pin bolts (1) and tighten them to 70 lb ft (95 N.m). NOTE: It is important to note which caliper pin is designed for the correct bore. The leading caliper pin, or top pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design. Ensure that the bolt boots fit securely in the groove of the pin bolts. Be sure not to pinch or tear the boots. If the boots are damaged, they must be replaced.
Why a pin sinks in water but a ship do not?
Because ship have lot of air inside it to make a pressure but a pin is a solid just like the case of balloon
How hard is it to move the Body-Solid Powerline PFID125 Flat Incline Decline Bench?
It is very simple just pull the pin, move and reinsert the pin.
Is the clutch of a tie tack pin made of gold?
The clutch of a tie tack pin can be gold plated but would not be solid gold; gold is a very soft metal, and it would not work for that purpose.
What is the purpose of the ZIF socket?
ZIF or "Zero Insertion Force" sockets allow the socket to open to receive the pin without pressure and then close around the pin to give a good, solid connection.
How do you determine the collector and emitter terminals of a phototransistor?
Answer: First you have to find the Base, with your millimeter set to diodes play around with the probes between the three pins until you get a reading between one pin to both the other two pins that pin will be your Base, if your red probe is on that pin then it is a NPN transistor, if it is the black probe then it is a PNP, there will be a slight difference in the reading, the pin with the smallest reading will be the Collector and the larger is the Emitter
Why is the live pin getting hot on a three pin plug?
Heat is caused by a current trying to flow through a resistance. What you have is probably a loose connection on one of your screw terminals of the plug creating a higher than normal resistance. Take a screw driver and tighten the screws and see if that makes a difference.
Is Blackberry messenger compatible with aim?
Unfortunately, no - it's a distinct application that uses an inimitable protocol to send messages to other terminals (i.e. implicit Blackberry PIN IDs - unique to RIM hardware).
