answersLogoWhite

0

A transistor has three leads, called the base, the collector, and the emitter. The voltage of the base (in relation to the ground) determines whether and how much current flows from the collector to the emitter. An NPN transistor can be off, meaning that there is no (or very little) voltage from the base; partly on, meaning that there is some voltage from the base; or saturated, meaning that it is receiving full voltage from the base. A saturated transistor allows the current to flow from the collector to the emitter unopposed; a partly on transistor provides some resistance; and a transistor that is off provides full resistance. A PNP transistor is similar to an NPN transistor except it performs the opposite function: when it is saturated, the current is fully resisted; when there is no voltage from the base, the current is not at all resisted; and when it is partly on there is some resistance.

In sum, a transistor controls the flow between the collector and the emitter based upon the voltage of the base. this is carbage. a transistor is basicaly two diodes back to back base being common TO BOTH DIODES because of inpurity doping on purpose at the depletion region the transistor will control the current flow on the other diode. Once it reaches saturation both diodes conduct therefore current can flow in BOTH DIRECTIONS ACROSS IT.

User Avatar

Blaze Rogahn

Lvl 10
2y ago

What else can I help you with?

Related Questions

What is the function of the legs on a transistor?

as the name suggest transistor means to transfer resistor, it is an electronic device,


Function of resistor capacitor and transistor on integrated circuit?

resistor


What is a function of a transistor?

To allow current to flow in only one direction.


What can the input of a transistor be called?

The input of a transistor is typically referred to as the "gate" in a field-effect transistor (FET) or the "base" in a bipolar junction transistor (BJT). In both cases, the input controls the flow of current through the transistor, allowing it to function as a switch or amplifier in electronic circuits. The gate or base receives the input signal that modulates the transistor's operation.


Function of transistor BC 558 in musical bell?

it cnverts to a low voltage.


Transfer characterstics of transistor-transistor logic family?

A: The characteristic will be the same as DTL RTL TTL the logic will not change but the transfer function for each family is certainly different


How did the word transistor originate?

The word "transistor" is a blend of "transfer" and "resistor," reflecting its function of transferring electrical signals across a resistor. It was coined by John R. Pierce, an engineer at Bell Laboratories, where the first transistor was developed in 1947.


Can a transistor alone perform the function of an amplifier?

No, it needs several other components and a source of power.


What is difference between transistor biasing and connection?

Transistor biasing is a function of implementing a DC support circuit that places the transistor in an electrical region that produces the desired output signal in relation to its input signal, according to its design specification. A transistor can be biased to create a linear amplified signal proportional to its input. Biasing can also place the transistor into an easily saturated condition to propagate clipped binary output relative to its input. Biasing refers to the component configuration designed around a specific transistor family. Connection refers to the simple function of making an electrical junction between two conductors.


Why a transistor is a non linear devices?

A: THE WORD IS LINEAR. yes it is not a very linear device as a function of current


What is DC load line of a transistor?

A: A transistor has voltage gain as base current is allow to flow. If the load is constant then a DC mirror azimuth path can be plotted as a function of base current and collector current and that is the load line


How do you test a transistor using cathode ray oscilloscope?

Yeah...its possible to test the transistor using Cathode Ray Oscilloscope (CRO). CRO provides a function called "Component Testing". Just connect the transistor terminals between two pins provided by this function and you can observe the patterns on the CRO screen. Normally, in case of transistor, The operation is divided in few parts. 01. Observe the pattern for CB configuration. ---- For this, connect the terminalsfrom CRO between this Collector and Base terminals and you can observe the pattern shown by CRO. Same procedure should continue for CE & BE configuration so as to test the transistor.