0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why use link in star contactor?
The link in the star contactor is used to form the star point of three of the motor leads. On most star wound motors the star point is inside the motor windings. On a motor that can be used for star delta starting it is a six wire motor. The star point winding depends on the contactor to tie the coil ends together externally in the control panel of the star delta starter.
A device with a overload protection used to control a motor is a?
A device with an overload protection used to control a motor is an Overload Relay.
Speed control of motor using SCR?
An SCR chip is commonly used to control the speed of a motor. The speed is controlled using an AC circuit and phase angles.
Why is a star-delta starter used?
A "star-delta" starter- also known as a "Y-delta" or "wye-delta" starter - is used to reduce the voltage on the motor windings to only 1/.'/'3 [one divided by root 3] times the incoming line voltage, to help reduce mechanical stress and in-rush current at start-up.More detailWhenever you start a big heavy electric motor, you need to start it slowly to prevent the rotor overheating and drawing an enormous current. When the windings of a 3-phase motor are connected in STAR the voltage is reduced to a fraction equal to one over root three (1 / 1.732) times the normal running voltage that is used when it is connected in DELTA, resulting in a reduction of nearly one half the normal current.Once the motor picks up speed, the connection is changed to DELTA so that the motor runs at full speed and torque from then on. It's a bit like using the gears of an automobile.For more information please see the answers to the Related Questions shown below.
Is 4 point starter used to start and control the speed of dc shunt motor with armature resistance control?
yes
How much KW range can be use star-delta starter?
The use of a star delta starter is for motor control only and not resistive heating loads. This type of starter is used to dampen the inrush current by using a lower voltage to start the motor.
Why use link in star contactor?
The link in the star contactor is used to form the star point of three of the motor leads. On most star wound motors the star point is inside the motor windings. On a motor that can be used for star delta starting it is a six wire motor. The star point winding depends on the contactor to tie the coil ends together externally in the control panel of the star delta starter.
What component used to start a modern induction motor?
Star delta starter
Where can someone purchase an AC drive?
One can purchase an AC drive at DriveSys, Vacon, EmersonIndustrial, Delta or GETransporation. An AC drive is a device used to control the speed of an electrical motor.
A device with a overload protection used to control a motor is a?
A device with an overload protection used to control a motor is an Overload Relay.
How do you connect motor by star delta starting?
starter is used to limit the starting current to save the motor. for star-delta first star mode is enabled so the applied voltage is reduced to safe value after the motor catches the rated speed the mode is changed to the delta mode. hence the full supply voltage is applied to the motor.
What is vf speed control?
It is used for sensorless motor control. With vf speed control u can control speed of any induction motor.
What is speed controller?
It is used for sensorless motor control. With vf speed control u can control speed of any induction motor.
Why star delta timer required for motor?
The timer is used to give the motor time to reach its running speed at the star voltage. Once the timer times out the star contactor drops out and the delta contactor pulls in.
Why motor protection circuit breaker is not used in star delta starter?
please you give me reply to answer.
How can a relay be used to run a 9V electric motor?
A relay cannot be used to power a motor. It can be used to control the motor by wiring the motor circuit in series with the relay contacts.
What materials are used to make a drill?
Plastic, rubber, metal and a motor
