The hazard of compressed air (and all other compressed gases) is often underappreciated. If compressed gas is uncontrollably released it can propel tanks weighing 200 pounds with enough energy to bend I-beams in commercial buildings and still fly for hundreds of yards. This concern decreases as the pressure decreases. So tanks of compressed gas must be well secured in storage and use, and their valves must be protected from damage
Other precautions include the following.
For Tanks: corrosion, dents/damage, valve operation, seals, welds, and especially the protective guard around the valve. Most types of compressed gas tanks require testing and re-certification regularly (annually, every 5 years, etc). For typical air compressors, follow the manufacturers instructions for draining the tank (to prevent internal corrosion) and drier use/inspection/replacement.
For lines/tools: High pressure lines must be secured with a tether at their connection points to prevent wild flailing lines. For all lines ensure regular lubrication of the connectors, and inspection of rubber lines for abrasion, chemical damage, cracking etc. The same for air tools. Do not modify any air tool. Even the holes on the side of a compressed air blower or nozzle are there for a reason. Air at over 20 or 30 psi can cut through skin. The holes make that impossible by ensuring that nozzle pressure cannot rise above a set point, even if the nozzle opening is blocked.
To make compressed air safe to breathe it must be treated. In general, a four cycle dryer is used to purge and remove contaminants from the air.
Safety precautions applicable to metal working depend on the kind of metal working being attempted. They might include:wear industrial safety glasseswear face shieldwear gloves appropriate to the workguard belts and pinch pointskeep hands and feet out of the working points of machines and tools
Seek guidance from the supplier or manufacturer.
i think , because water tanks are more vulnerable structures and plus the tank is sometime overfilled and sometime empty, the pressure inside is so varying, its needs more safety precautions and as we all know working stress method assumes more safety factor than limit state design, which is an economical design, we prefer to use working stress method...
no idea at all.... Otherwise you'd have known it by now !!! Sorry.
The working conditions for a safety engineer is to identify, anticipate and evaluate the hazardous practices and conditions.
There are several safety precautions that should be followed on the street. Namely, it is wise to travel in groups, and avoid areas that are not well lit.
The safety precautions that should be used when working with calcium depend on the form of calcium you are working with, what you will be doing with it, and how much you will be handling.
what are the safety precautions in bench working
The compressed air health and safety symbol means that a source of compressed air is present and you should take the precautions you have been taught to prevent being injured by it.
The primary precaution when working on any capacitor is to ensure that the capacitor is disconnected from electrical sources and that it has been fully discharged.
What safety precautions you can take when working in a factory depends on what is done in the factory and how it is done. An answer to such a general question would usually fill several books.
safety precautions for a scriber
There is a few precautions you should take when working with sheet metal. You should always wear safety glass, wear gloves an pay attention.
Yes, they have lots of safety precautions.
Failure to follow safety precautions outlined in the Health and Safety at Work Act 1974 can result in accidents, injuries, or even fatalities in the workplace. This could lead to legal consequences, financial penalties, damage to the company's reputation, and loss of employee morale and productivity. Moreover, non-compliance with the Act can create a hazardous work environment for employees.
Safety precautions applicable to metal working depend on the kind of metal working being attempted. They might include:wear industrial safety glasseswear face shieldwear gloves appropriate to the workguard belts and pinch pointskeep hands and feet out of the working points of machines and tools
There are a few types of safety precautions when working in a lab. For instance, there should be an eye-wash station in case chemicals get in the eyes. There should be gloves available to use, along with goggles, and protective clothing. The lab should also contain a fire-extinguisher.