0
What are the torque settings and tightening sequence for the rocker box bolts on a Harley Davidson shovelhead engine?
Wiki User
∙ 8y ago
The rocker box bolt torque specifications, on your Harley-Davidson, is 15 pounds per square inch. The bolts should be torqued in five pound intervals.
Garnet Zemlak
Add your answer:
Earn +20 pts
What are the torque settings and tightening sequence for the rocker box bolts on a Harley Davidson shovelhead engine.?
The rocker box bolt torque specifications, on your Harley-Davidson, is 15 pounds per square inch. The bolts should be torqued in five pound intervals.
What are the torque settings and tightening sequence for a 1.6 k series rover engine?
What_are_the_torque_settings_and_tightening_sequence_for_the_cylinder_head_bolts_on_a_Rover_200_K-series_engine
What are the torque settings and tightening sequence for the cam box on a rover 200 t series?
Rover 20T2N 2.0Ltr Diesel engine Cam cover torques are listed as 12 Nm. No tightening sequence is listed .
Torque settings and tightening sequence for head bolts mg zr 160?
20nm +180 degree +180 degree
What are the torque settings and sequence for tightening head bolts on a land rover range 4.0 v8?
The torque settings are 40 to 45lb/ft for the outer row, 65 to 70 for the centre to inner row. Haynes (Methuen & Coomber 1999) doesn't specify any particular order for refitting the head bolts; follow the standard automotive practice of tightening the ones furthest apart and moving inwards.
What are the cylinder head torque settings on a 1989 Toyota Town-Ace 2.0 liter with a 2CT engine code?
I was just on the Toyota Owners Club site and found this information from Martin_Longbow; Toyota Carina E 2.0Ltr D Turbo 1996 - 98 (2C-T) Head tightening sequence (new bolts not required) Stage 1, 44 Nm Stage 2, Tighten 90 Degrees Stage 3, Tighten 90 Degrees On the older ones there is a four stage sequence and there are 18 bolts according to the diagrame I have for the tightening sequence I hope it's of some help.
What are the Torque settings saxo 1.0 cylinder head?
The torque settings for aluminum head are; stage 1. 15lb ft. Stage 2 you have to set the correct torque level by angular measurement, angle tighten a further 240 degrees. Cylinder head tightening sequence is important if you do not want to warp the head. Get down to your local library go to the technical section and photocopy the section from the Haynes manual
Torque settings for citroen saxo cylinder head bolts?
in sequence torque bolts to 20nm, then again in sequence turn a futher 120 degrees, and again in sequence 120 degrees.
What are the torque settings and tightening sequence for the cylinder head bolts on a Rover 200 K series engine?
20nm then 180degrees then another 180 degrees Left to right back row 9,5,1,3,7 (back row nearest windscreen) Left to right front row 10,6,2,4,8 (front row nearest radiator)
What is the head bolt sequence and torque settings for a ae86 Toyota carolla?
Refer to the factory manual for correct sequence. Loosening sequence if different to tightening, and both should be done in steps, not all at once. Lightly oil thread and under head of bolts and torque as instructed in the manual. Use a new head gasket and clean the head and block surfaces. Take care not to scratch or damage the sealing surfaces. Use a torque wrench and the proper 10mm 12 point deep socket.
Where can one purchase Harley Davidson sunglasses?
Harley Davidson is a licensed brand that can be purchased in dealerships, outlet stores and optical labs for prescription settings. As with all licensed brands, to be certain that you are purchasing the real brand and not a knock off, the Harley Davidson dealership is suggested.
What is the cylinder head torque settings of the opel astra 1600 16 valve ecotec motor?
torque specs in Nm and tightening esquence
