0
Refer to the exhibit. A network administrator successfully pings R1 from R3. Next, the administrator runs the show cdp neighbors command on R3. The output of this command is displayed.What are two reasons for the absence of R1 in the output? (Choose two.)
~
**The no cdp run command has been run at R1.
**The no cdp enable command has been run at Fa0/1 interface of R3.R1 is powered off.
What else can I help you with?
What does a voltage divider do and how does it work to divide the input voltage into smaller output voltages?
A voltage divider is an electrical circuit that divides the input voltage into smaller output voltages. It consists of two resistors connected in series. The output voltage is determined by the ratio of the two resistors. The formula for calculating the output voltage is Vout Vin (R2 / (R1 R2)), where Vin is the input voltage, R1 is the resistance of the first resistor, R2 is the resistance of the second resistor, and Vout is the output voltage.
What two pieces of information can be detemined from output?
R1 is originating the route 172.30.200.32/28. Automatic summarization is disabled. The 172.30.200.16/28 network is one hop away from R1. A classful routing protocol is being used.
What would the tracert output be if r1-isp failed?
Nothing reach after r2 central.
Derive the output equation for differential amplifier and instrumentation amplifier?
Vo=(R2/R1)(V2-V1)
What are back buttons on a ps2 controller?
r1 r1 and l1 l2 like right one right two and left one and left two you get it?
Are there any cheat codes for madden 09 for PS2?
yes press R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2,R1,R2, then press select to complete the entire game
How do you calculate output voltage?
The output voltage can be calculated using Ohm's Law, which states that V (voltage) = I (current) * R (resistance), where I is the current flowing through the circuit and R is the resistance of the circuit. Alternatively, you can use the voltage divider formula Vout = Vin * (R2 / (R1 + R2)), where Vin is the input voltage and R2 / (R1 + R2) is the voltage divider ratio of resistors R1 and R2.
What is the relationship between a planets distance from the sun and distance between planets?
If two planets are in orbits with radii of R1 and R2, the distance between them varies from R2-R1 to R2+R1.
Were does Rt R1 R2 comes from?
Rt = R1 + R2 That's the formula for the total effective resistanceof two resistors in series.
How do you write quadratic equations using roots?
If the two roots are x = r1 and x = r2 then the quadratic equation is: (x - r1)(x - r2) = x2 - (r1 + r2)x + r1r2 = 0
Host A is unable to reach the networkon the basis of the provided output what is the cause of the problem?
There is no path to the remote network in the routing table of router R1.
What Is Nine tenths divided by two fifths?
2 r1
