0
What else can I help you with?
How do you tighten a loose air conditioner compressor in a 93 dodge caravan 3.3 engine?
It you are talking about the lower bolts then you need to remove the drive belt and the top compressor bolts and slightly move the compressor to the side and then tighten up the lower bolts and remember that you do not need to discharge the a/c system................
What is a wrench that does't tighten bolts?
Every proper wrench will tighten or loosen bolts. -If this is a riddle or joke, please enter it in that category.
Torque specs 4.7 dodge Dakota head bolts?
* Step 1: Tighten bolts 1-10, 20 N·m (15 ft. lbs.). * Step 2: Tighten bolts 1-10, 47 N·m (35 ft. lbs.). Tighten bolts 11-14, 25 N·m (18 ft. lbs.). * Step 3: Tighten bolts 1-10, 90 degrees. Tighten bolts 11-14, 30 N·m (22 ft. lbs.).
What kind of wrench is used to tighten nuts and bolts to a specified amount?
A torque wrench is used to tighten nuts and bolts to a specified amount
What size allen wrench do I need to tighten the bolts on my bike pedals?
To tighten the bolts on your bike pedals, you will need a 6mm allen wrench.
How do you tighten the bolts on a 87 Oldsmobile?
What bolts? Usually with some sort of wrench!
How do you tighten chain on 2003 Suzuki z400?
Loosen the top two bolts on the swing arm, after tighten the two bolts on the rear of the swing arm until you have 1.5"-2" of slack. Tighten the top bolts back up and good to go
What is spanner used for?
To tighten bolts and nuts
Torque specs big end bearings Toyota 3l 2.8l diesel?
For new bolts(1st time) tighten to 34nm, then tighten a further 120degrees For used bolts(2st time) tighten to 54nm, then tighten a further 90degrees
How can I tighten the headset on my bike?
To tighten the headset on your bike, first loosen the stem bolts on the handlebars. Then, use a wrench to tighten the top cap bolt on the headset. Finally, retighten the stem bolts on the handlebars.
What is head bolt pattern for 2006 4.7 liter Dodge?
he cylinder head bolts are tightened using an angle torque procedure, however, the bolts are not a torque-to-yield design. 6. Tighten the bolts in sequence using the following steps and torque values: Step 1: Tighten bolts 1-10, 20 N·m (15 ft. lbs.). Step 2: Tighten bolts 1-10, 47 N·m (35 ft. lbs.). Tighten bolts 11-14, 25 N·m (18 ft. lbs.). Step 3: Tighten bolts 1-10, 90 degrees. Tighten bolts 11-14, 30 N·m (22 ft. lbs.).
Subaru 2.2 Head torque specifications?
{| |- | NOTE Step 1: Tighten all bolts to 22 ft. lbs. Step 2: Tighten all bolts to 51 ft. lbs. Step 3: Loosen all bolts, in reverse torque sequence, by 180° Step 4: Loosen all bolts, in reverse torque sequence again by 180° Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs. Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs. Step 7: Tighten all bolts, in torque sequence, by 80-90° Step 8: Tighten all bolts, in torque sequence, again by 80-90° |}
