0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
When voltage increase then current will be?
it depends on what type of load. Motor amperage will drop off as voltage rises. loads such as lights will increase amperage with voltage rise.
Will 220 volt work in a high volt 3 phase motor?
Yes a 208 voltage motor will operate on 220 volts. You have to increase the motor overload protection by 10% of the motor's full load amperage to protect the motor.
What is overload protection?
It is protection installed to protect, usually motors, from going beyond the amperage capacities that were set down by the manufacturer's specifications of the motor. As a motor loads up to its rated HP it will operate within the motors amperage range. More loading on the motor will increase the amperage draw to a point where the motor's winding will start to burn or short out due to insulation breakdown of the motor coils. Over load protection is a settable device that will limit the current to a specific value. The setting on the over current device is the motor's FLA (full load amps). If the motor amperage goes higher that the set point the overload protection, the overload protection contacts will open and drop the motor's magnetic contactor off line. In some cases this could be an annoyance but it does save the motor from destroying itself.
What does LRA mean in electrical terms?
Locked rotor amperage is the amperage the motor draws when the voltage is first applied to the motor and the rotor has not started to turn. This amperage is usually up to 300% of the motors running amperage. Once the rotor starts to turn the motor generates a back EMF (electro motive force) that opposes the high inrush current. This back EMF drives the amperage down until the motor gets up to its rated speed at which time the motor amperage will be at its run amperage.
What is the FLA at 230 volts with nameplate amps of 20 and voltage of 230?
If the nameplate states 20 amps then that is the full load amperage when the motor is running. The start up current on the motor could reach 300% of the FLA depending on the type of motor and the load that is connected to the motor.
When voltage increase then current will be?
it depends on what type of load. Motor amperage will drop off as voltage rises. loads such as lights will increase amperage with voltage rise.
Can you run a motor of greater amperage draw with a motor of less amperage draw?
It looks like you are asking if a higher amperage motor can replace a lower amperage motor. It depends on what the amperage difference is. If the amperage is high enough to move the capacity of the wire out of its rated value then it should not be done.Remember motor conductors have to be rated at 125% of the motors nameplate amperage. As the amperage increases so does the HP and the motor's protection will also have to be increased or the motor will trip the lower overload protection settings.Also keep in mind that if the motor is three phase, running a motor with higher HP on a load that does not need the extra HP, it will lower the power factor of the supply distribution.
Will 220 volt work in a high volt 3 phase motor?
Yes a 208 voltage motor will operate on 220 volts. You have to increase the motor overload protection by 10% of the motor's full load amperage to protect the motor.
What is overload protection?
It is protection installed to protect, usually motors, from going beyond the amperage capacities that were set down by the manufacturer's specifications of the motor. As a motor loads up to its rated HP it will operate within the motors amperage range. More loading on the motor will increase the amperage draw to a point where the motor's winding will start to burn or short out due to insulation breakdown of the motor coils. Over load protection is a settable device that will limit the current to a specific value. The setting on the over current device is the motor's FLA (full load amps). If the motor amperage goes higher that the set point the overload protection, the overload protection contacts will open and drop the motor's magnetic contactor off line. In some cases this could be an annoyance but it does save the motor from destroying itself.
What size breaker is needed for a 125 hp motor?
It depends on what the amperage of the motor is. The motors amperage depends on the voltage of the motor. The higher the voltage the motor operates on the lower the amperage. So unless the amperage from the motor's nameplate is stated an answer can not be given.Just remember that the feeder capacity to the motor has to be 125% of the motors full load amperage and the breaker protecting the conductors to the motor has to be rated at 250% of the motors FLA. This higher breaker size allows the motor to start without tripping a normal size breaker that is rated for the lower conductor size.
What is the formala for max overload on three phase motor?
The maximum overload on a three-phase motor can be calculated using the formula: Maximum Overload = (Full Load Amps / 100) x Percentage Overload Where Full Load Amps is the rated current of the motor at full load, and Percentage Overload is the desired amount of overload.
What does LRA mean in electrical terms?
Locked rotor amperage is the amperage the motor draws when the voltage is first applied to the motor and the rotor has not started to turn. This amperage is usually up to 300% of the motors running amperage. Once the rotor starts to turn the motor generates a back EMF (electro motive force) that opposes the high inrush current. This back EMF drives the amperage down until the motor gets up to its rated speed at which time the motor amperage will be at its run amperage.
Why does my 99 Ford Windstar power seat fuse keeps burning out intermittently?
Usually if a seat motor is causing the fuse to blow then the motor is going bad. It could be using more amperage than it is designed to use. This will cause the fuse to blow. DO NOT be tempted to put in a bigger fuse. This can cause a fire. Good luck.
How much amperage is drawn by a kiloWatt motor?
To answer this question the motor voltage is needed.
If my AC technician says my unit is rated at 28.9 amps and drawing 24.8 and should draw about half of rated capacity and that compressor needs to be replaced Is this correct?
There are several amperage ratings on AC compressors/motors. Locked Motor Amperage (LRA) is the amperage that the motor is fused for. The load of the motor is expressed in amperage or wattage, which is probably the case here. Low amperage readings on an AC unit being charged by amperage load would indicate low freon. High amperage readings indicate overcharge when charging by the amperage load. AC units are not accurately charged by amperage readings and the efficiency of motors is not expressed in amperage readings.
Is a bad motor starter on your car that draws a lot of amperage going to wear out your alternator more quickly?
a Bad starter will 1. Cause your battery to run faster to dieing. 2. yes, it will wear your alternator out faster and could result to ruining it.
What will happen to a motor if it is supplied with lower voltage than its rated voltage?
The amperage to the motor will go higher.
