answersLogoWhite

0

A mat!

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Why when you step out the shower and it warm you shiver?

i think because you were in a warm shower and you are not used to how warm it is when you step out of the shower


What are the main benefits of a walk in tub shower?

A "walk-in" tub/shower eliminates the need to step over the side of the tub to get in and out of the bath or shower. Older people and individuals with disabilities or injuries (as well as caregivers) find it much easier and far safer to use a walk-in tub/shower.


How hard is it to install steam shower enclosures?

It shouldn't be that hard. Here is a good site that shows step by step. http://www.diynetwork.com/how-to/how-to-build-a-tile-backsplash-for-the-shower/index.html


What do you do with the hair drier in shrink ray island?

use it to get into the shower Turn it on step over the edge go into shower


Why does your period stop when your in the shower?

It doesn't, when you step into the shower, all the blood is washed from the outside of your vagina but not the inside. You still have your period.


Is there a website that gives instructions to tile a shower?

There are many sites which provide guidance in tiling a shower. Some of these are Hgtv, Wikihow and Homerenovations. Look into Youtube to see actual step by step videos.


How do you use a shower?

Turn it on, step in, get wet. Turn it off, apply soap and shampoo. Step in, turn it on, rinse. Turn off, step out.


How do you take a group shower?

Get People To go in the shower lol!


Do all people take a shower regularly?

People of any ethnicity may shower in the same manner.


How to Create Your Own Dream Bathroom by Building a Walk-in Shower?

Many people have decided to replace their bathtubs with walk-in showers. This could be because you have the ability to create a walk-in shower any way that you want. You can even install multiple shower heads and seating inside. The process of installing a walk-in shower is easy, but it will take patience and time. These are the steps needed to take in order to build and install a walk-in shower: The first step is to clear out the space by removing the tub/shower. Make sure no debris is left in the space and clean it thoroughly before proceeding to the next step. The second step is to readjust the drain. You can leave the existing drain where it is and run a show pan to the middle of the new shower. This helps because the show pan is attached to the drain. The third step is to form the walls that you are going to use for the shower. The walls should be made from 2x4 lumber. Each wall should have a sheet that is made of mold resistant tile backer board and water covering it. The fourth step is to work on the flooring in the shower. All you have to do is pour in a concrete slab. Let it set and dry before moving on. The fifth step is to turn off the water completely, tap into the water supply, and install the shower heads. Make sure that the shower heads work and that there are no leaks. The sixth step is to make any repairs necessary to the walls and ceiling if they were damaged while you were installing the shower heads. The seventh step is to lay the tiles down on the ceiling, walls, and floor. Stick the tiles to the concrete/lumbar with a thin set mortar. Make sure to use grout to fill in the spaces. After the grout has set for a half an hour, wipe it down with a wet cloth. Finally let the grout continue to set and dry for a full day.


How To Install a Massaging Shower Head?

At the end of a long day, few things feel better than using a massaging shower head on your neck, shoulders and scalp. The hot water pounding on you can relax your muscles and prepare your body for a good night’s sleep. A massaging shower head isn’t expensive, and you can install it yourself with a few simple tools. Step 1: First you have to remove the old shower head. Use a chair or stool in your shower so you’re at a good angle to work on the shower head. Try a crescent or adjustable wrench first to loosen the nut holding on the old shower head by turning it to the left. If the nut is too tight or is held on with calcium build-up, you’ll have to use Vise-Grips to remove it. If you do this, be very careful to twist only the nut, not the shower arm. You do not want to break off the shower arm. Step 2: Use a cleaner and a small brush to clean the threads on the shower arm. Remove as much residue and build-up as possible. Let it dry thoroughly. Step 3: Wrap the threads of the shower arm with plumber’s tape. Most new shower heads include plumber’s tape in the package, but don’t skip this step even if you have to buy a roll of tape separately. Step 4: The next steps may vary somewhat based on your individual model of massaging shower head. Be sure to read and follow all package directions. In most cases, you’ll slide a washer onto the shower arm, followed by the shower head. Be careful to line up the threads on the shower head nut with the threads on the shower arm. If they don’t line up right, your shower head will leak. Step 5: Use a wrench to tighten the nut on the shower head. If it starts going crooked, loosen it and try again. Step 6: When the nut is fully tightened, turn the shower on and inspect the shower head carefully for any leaks around the nut. If you find a leak, turn the shower off, dry the shower head and tighten the nut further. If that doesn’t fix the problem, you may have to remove the shower head, add more plumber’s tape and screw the shower head on again.


What are the steps to make a complete shower after the drain is set?

The center of the shower floor where the tile shower drain would normally be positioned ... drain base. After this step the sloped mortar bed should be ... pan liner or membrane in our instructions.