answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered
2011-09-13 10:42:40
2011-09-13 10:42:40

u need to relaese tension on the tension pulley. this is usually done with a long socket wrench handle. when u release tension and remove belt you then release tension on pulley until you have routed new belt . you then move tension pulley again until you can put belt on it, then release pulley and it will automatically provide correct tension

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


loosen the alternator and it will slide right off Check 2carpros.com for a belt routing diagram.


A ratchet isÊneeded to loosen the serpentine belt tension pulley on a 2002 Jeep Wrangler V6. It will require a 1/2 inch ratchet.


On the power-steering bracket, you'll see a bolt going into it vertically from about the 11 o'clock position. this bolt is very long, but you may not be able to tell. loosen this bolt and back the PS pulley bolt out a few turns and everything will go slack, allowing belt replacement.


You will need to loosen the tensioner pulley in order to create slack in the serpentine belt. The belt will come off with the tensioner pulley loose. Reverse the process to install the new serpentine belt.


Find the appropriate size socket to go on the belt tensioner, put it on a ratchet or breaker bar. Rotate the belt tensioner counterclockwise, and that'll loosen the slack and allow you to remove the serpentine belt.


Loosen the tensioner pulley on your Mercedes-Benz. The serpentine belt will become loose and can be removed. Put the new serpentine belt on and tighten it with the tensioner pulley.


You can loosen your 1995 Chrysler Town and Country serpentine belt by loosening the tensioner pulley. Push the loosen the tensioner pulley to the right. The old serpentine belt can be easily removed. Put the new serpentine belt on and tighten the tensioner pulley by pushing it to the left.


loosen the bolt. There should be a sticker with a diagram under the hood.


Subaru 4 cylinder does not use a serpentine belt. The 6 cylinder instructions are rather simple, same as my '88 Cavalier and I presume any car that uses a serpentine belt. This comes from the factory service manual: remove collector cover install tool to tensioner pulley installation bolt rotate tool clockwise to loosen the belt and remove install in reverse order


Loosen the tensioner pulley on your 2004 VW Jetta. The serpentine belt will become loose and can be removed. Put the new serpentine belt on and tighten the tensioner pulley.


Changing the serpentine belt on a 97 Mitsubishi Diamante is a fairly easy task. All you need to do is get a wrench and loosen the tension pulley and pull of the serpentine belt.


buy a belt, loosen the tensioner, replace belt


You will need to loosen the tensioner pulley on your 1994 Pontiac Grand Am. The old serpentine belt will come loose and can be removed. Put the new serpentine belt on and tighten the tensioner pulley.


Loosen the tensioner pulley. Pushed the tensioner pulley to the left. The serpentine belt will come loose. Remove the belt. Reverse the process to install the new serpentine belt.


You will need to loosen the serpentine belt tensioner pulley on your 2002 Chevrolet Avalanche. Slide the belt tensioner to the right. The serpentine belt will become loose and can be removed. Reverse the process to install the new serpentine belt.


Loosen the tensioner pulley on your 1988 Chevrolet Corsica. When the tensioner pulley is loose the serpentine belt will easily come off. Put the new serpentine belt on and tighten the tensioner pulley.


loosen the tensioner assenbly with a 1/2" drive ratchet or a serpentine belt tool and reinstall the belt according to the diagram under the hood


Spring loaded belt tensioner on the lower driver side.


The serpentine belt on a 2003 Toyota Rav4 can be loosened by turning the retaining bolt on the idler pulley. The belt can then be shifted inward to loosen.



it is adjusted throught the power steering pump loosen the adjuster bolts remove belt and reverse


You'll have to loosen the alternator to get the belt off, unless you have a tensioner pulley in the sequence of the serpentine. yes it removes the tension to make it easier just did it last weekend.


To change the serpentine belt on a 1988 Mercury Cougar, first take a picture of how the old belt is put on. Then, loosen the nut on the tension pulley and remove the old belt. Use the picture to route the serpentine belt in the same pattern as before. Tighten up the nut on the tension pulley.


The power steering unit and the alternator are both driven by the serpentine belt. Loosen the tensioner pulley and the serpentine belt will become loose. Put the new serpentine belt on and tighten the tensioner pulley.


Loosen the tensioner pulley. The serpentine belt will become loose and can be removed. Put the new serpentine belt on and tighten the tensioner pulley.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.