0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What does 1 and 2 mean on an electrical switch?
If there is another terminal marked L, then the 'Hot' wire comes from the breaker box to the L, 1 will deliver a low voltage to the appliance, and 2 will deliver a higher voltage.
How does an electric switch help in an electric circuit?
A switch is a means of making (on) or breaking (off) an electrical circuit.
How you can check relay?
Do you mean: 1. electrical relay, an electromechanical switch, 2. data relay, sending data from one node to another, or 3. some other use of the word "relay"? Clarification, please
Can you switch from 1 type of braces to the next?
if u mean like metal to plastic. no
What does the 0 mean in a power switch?
0 means "OFF" whilst 1 means "ON"
How to remove brake switch in mercedes benz model clk430?
The brake light switch is located on the brake pedal assembly. 1. Remove the cover below the instrument panel 2. Remove the electrical connector. 3. On the switch their is a locking tab the prevents rotation. Press the "tab" and rotate the switch 90 degrees. 4. Remove switch.
You just bought an 87 buick park ave and all the lights work except for the brake lights what could that be and is it hard to fix?
is the simplest thing to fix in a vehicle, 1 go under your dash board follow the brake peda up and you'll see a switch(electrical conection) attached to it. that is the brake light switch 2 removed the electrical wire going to it and either unscrew or "un-pin" the switch.(piece of cake) 3 buy the same switch and re attach it in the same order that you took the old one off. if you have 2 switches o your pedal disconect the one that only has an electrical conector . because the one that has electrical conector and a hose is not a brake light switch that is your cruise control reset switch.(if your car is equiped with it)
What does the letters I and O mean on a switch?
They are the numbers 0 and 1; each comes from binary notation, where 0 is off and 1 is on. I/O can also stand for Input / Output. In todays world it would be more likely to be understood by using the ( circle with an electrical symbol inside for ON ) and the( circle with the slash through the electrical symbol for OFF ). Respectfully Yours, Richard W Clothier PO Box 25,Legal, Alberta, T0G1L0.
How do do you replace the rear brake switch?
1. Locate the switch near the top of the brake pedal and take off the electrical connector. 2. Loosen the lock nut and unscrew the switch 3. Installation is the reverse of these steps. 4. To adjust the switch turn it clockwise until the plunger just touches the brake pedal, then turn it 1/2 turn more and tighten the lock nut.
How to Replace 5.9 dodge diesel oil pressure switch?
You will need to go to your local parts store and make sure to get the correct oil pressure switch or if you have a local Cummins dealer you can ask them. I got mine there for a third of the lowest price. It is located on the drivers side of the motor and is be hind some electrical connections so it is hard to see. It is closer to the front of the motor. It takes either a 1 1/4 inch or 1 1/6 inch socket. Make sure and get it tight as to not have a leak but not over tighten and strip. Also MAKE SURE AND GET THE RIGHT SWITCH. If you get the wrong switch or the some of the single lines you may have to reprogram your ECM. If you are not experienced DONT TRY THIS. H&N Auto, Boise Idaho
Reverse motor for phase three?
If you mean to reverse the direction of a three phase motor, you just switch any 2 leads. switch 1 and 2, or 2 and 3, or 3 and 1.
What do you mean by calibration?
calibration is ocmpression between two part 1)electrical (AC,DC VOLTAGE ,CURRENT,RESISTANCE) 2)non electrical (PRESSURE,TEMPRATURE)
