0
In a fuse labeled T2AL 250V, the "L" stands for "Low breaking capacity." This indicates that the fuse is designed to break the circuit under low fault current conditions. The "T" signifies that it is a time-delay fuse, while "2A" indicates the current rating of the fuse, which is 2 amperes. The "250V" specifies the voltage rating of the fuse.
What else can I help you with?
Can you use a 250v 3a fuse to replace a 250v 3.15 fuse?
No
Is the f5l 250v fuse similar to f5a 250v and f5al 250v?
nope
Can 250v 2.5A fuse replace a 250v 3.15A fuse?
No, it is not recommended to replace a 250V 3.15A fuse with a 250V 2.5A fuse. The replacement fuse should have the same voltage rating, but the amperage rating needs to be equal to or higher than the original fuse to ensure proper protection against overcurrent.
Can T100L 250V fuse replace T80mA 250V fuse?
No, a T100L 250V fuse cannot replace a T80mA 250V fuse. The "T" indicates that it is a time-delay (slow-blow) fuse, while the numbers represent the current rating; 100L means 100 mA, and 80mA means the original fuse is rated for a lower current. Using a fuse with a higher current rating can pose a risk of overheating or damage to the circuit, as it may not blow in a fault condition. Always replace fuses with the same specifications to ensure safety and proper functioning.
What do the letters in T 6.3 A L 250V stand for?
T means Slow blow , 6.3A is the maximum current this fuse will conduct , any more and the fuse will heat up and melt the conductor . Maximum voltage capacity is 250V , this means the maximum voltage that the fuse can block from "jumping" . It means you can use it in a system from 0 - 250V with a maximum current handle of 6.3A .
What does T stand for in a fuse labeled T 2A 250V?
time delay
Can you use a 250v 3a fuse to replace a 250v 3.15 fuse?
No
Is the f5l 250v fuse similar to f5a 250v and f5al 250v?
nope
What is the current rating of T2L 250v fuse?
The current rating is 2A (2 amps).
What does F stand for in a fuse labeled F6A 250V?
Typically the "F" stands for "Fast Blow" or "Fast Acting". A "T", as in T6A, would mean "Time Delay" or Slow-Blow. So, an F6A 250 is a Fast Acting (Fast Blow) 6 Amp 250 Volt Fuse.
Can 250v 2.5A fuse replace a 250v 3.15A fuse?
No, it is not recommended to replace a 250V 3.15A fuse with a 250V 2.5A fuse. The replacement fuse should have the same voltage rating, but the amperage rating needs to be equal to or higher than the original fuse to ensure proper protection against overcurrent.
Can an F5L 250V fuse be switched out for a 5A 250V fuse?
yes it can but it may not protect as well the f5L is a fast blow fuse made to react quickly to the overcurent
What do numbers mean in t630mA 250v stand for?
In the designation "t630mA 250V," the "t" indicates that the component is a time-delay fuse. The "630mA" specifies the current rating, meaning the fuse will allow a maximum current of 630 milliamperes before it blows. The "250V" indicates the maximum voltage rating, meaning the fuse can safely operate at voltages up to 250 volts. Together, these specifications define the fuse's electrical characteristics and its suitable application in circuits.
What is the amps for Fuse T800L 250V?
T= timedelay 800= ? L=? 250V= volts
Can a F10AL 250V fuse be replaced with a F10A 250V fuse?
In most cases yes. but it depends on the application. The L in that model of fuse pertains to its ability to withstand destructive forces when it blows out.
Is a fuse labelled f6.3h 250v the same as 6.3a 250v?
Üretici: WickmannParça Numarası: F6.3H250VAmper: 6.3Voltaj: 250Malzeme: Seramik
Can a 3.15A 250v fuse be replaced with a 5A 250v fuse?
NO! The circuit wiring is protected by that 3.15 amp fuse. Put a 5 amp fuse in the circuit and the wiring may overheat and cause a fire. Never over-fuse any circuit even in an emergency.
