0
What does a Governor Pressure Solenoid Transducer andor Governor Pressure Sensor do?
Wiki User
∙ 15y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What are the repair cost for governor pressure sensor and the governor pressure solenoid?
Roughly $350 in parts and $150 for labor.
What are the codes readings p1762 and p1763 for a 1997 Jeep Grand Cherokee and how do you correct the problems?
P1762 Pretty sure that is "Governor Pressure sensor voltage too low." You will need part numbers: 4617210- solenoid and 56027720 and transducer. All you need to do is drop the pan and they will be in the passenger side front of the tranny on the valve body. P1762 Governor Pressure Sensor Offset Improper Voltage P1763 Governor Pressure Sensor Voltage Too High
How do you install governor pressure sensor for a 4.0L 2001 grand ckerokee?
Here's a link that will help. http://www.automotiveforums.com/vbulletin/showthread.php?t=350038&highlight=governor+pressure+transducer
Where is the 97 Dodge Dakota offset votage sensor located?
If you are asking about the code "governor pressure offset voltage" the governor pressure transducer is located on the valve body inside the transmission pan.
What is a delta pressure sensor?
It is a slang tern given to a Differential Pressure Sensor or Transducer.
How do you change governor pressure sensor and solenoid for 2004 jeep Cherokee Laredo?
I am going to give you the information for a 4.0L, if you have the 4.7L V8 let me know and I will send that informationThis is a fairly easy repair, when I do this I replace the governor pressure sensor and the transducer, that way you wont have to go back in if the other fails, you should also replace the filter while the pan is offHoist and support vehicle on safety stands.Place a large diameter shallow drain pan beneath the transmission pan.Remove bolts holding front and sides of pan to transmissionLoosen bolts holding rear of pan to transmission.Slowly separate front of pan and gasket away from transmission allowing the fluid to drain into drain pan.Hold up pan and remove remaining bolt holding pan to transmission.While holding pan level, lower pan and gasket away from transmission.Pour remaining fluid in pan into drain pan.Remove screws holding filter to valve bodySeparate filter from valve body and pour fluid in filter into drain pan.Dispose of used trans fluid and filter properly.Disengage wire connectors from pressure sensor and solenoidRemove screws holding pressure solenoid retainer to governor body.Separate solenoid retainer from governorPull solenoid from governor bodyPull pressure sensor from governor body.Remove bolts holding governor body to valve body.Separate governor body from valve bodyRemove governor body gasket.Before installing the pressure sensor and solenoid in the governor body, replace o-ring seals, clean the gasket surfaces and replace gasket.Place gasket in position on back of governor bodyPlace governor body in position on valve body.Install bolts to hold governor body to valve body.Lubricate o-ring on pressure sensor with transmission fluid.Align pressure sensor to bore in governor body.Push pressure sensor into governor body.Lubricate o-ring, on pressure solenoid, with transmission fluid.Align pressure solenoid to bore in governor bodyPush solenoid into governor body.Place solenoid retainer in position on governorInstall screws to hold pressure solenoid retainer to governor body.Engage wire connectors into pressure sensor and solenoidInstall transmission fluid pan and (new) filter.Lower vehicle and road test to verify repair.Parts should run right around $260.00 plus 2.0 hours labor
Where is the automatic transmission governor on 1999 dodge ram 1500?
This transmission uses an electronic governor. The pcm is the control. There is a solenoid and a pressure sensor on the valve body inside the pan.
On a 2001 dodge ram 2500 where is the transmission pressure sensor and governor solenoid on a 47RE?
They are inside the trans, on the passenger side of the valve body.
What is the error code P1762 on a 1997 ram van 2500?
There is a whole list of testing procedures but you need a DRBII scan tool to do the tests. SYMPTOM P1762-GOVERNOR PRESSURE SENSOR OFFSET VOLTS TOO LOW OR HIGH WHEN MONITORED Continuously with the key ON and the engine running. SET CONDITION This code will set if the governor pressure is out of range in park or neutral for 1.3 seconds for three consecutive bad 3.0 second tests and sump temperature > 10 �C (50 �F) and < 127 �C (260 �F) are required to set the code. POSSIBLE CAUSES Powertrain control module Powertrain control module - 5 volt supply high Powertrain control module - after 5 volt supply shorted to voltage Powertrain control module - after 5 volt supply shorted to voltage in trans Repair the 5 volt supply circuit and check the PCM Replace the trans solenoid assembly and check the PCM Intermittent condition Powertrain control module - internal fault 5 volt supply circuit open Check for other trans DTC's Governor pressure sensor signal circuit shorted to voltage inside trans Check trans fluid level and condition Governor pressure sensor signal circuit shorted to voltage Park neutral DTC present 5 volt supply circuit shorted to ground Governor pressure sensor signal circuit shorted to 5 volt supply circuit Governor pressure sensor signal circuit shorted to 5 volt supply circuit inside trans Governor pressure sensor signal circuit shorted to ground 5 volt supply circuit shorted to sensor ground Governor pressure sensor signal circuit open inside trans Governor pressure sensor signal circuit shorted to sensor ground GOV pressure sensor signal circuit open Governor pressure solenoid Governor pressure sensor signal circuit shorted to ground inside trans Powertrain control module - 5 volt supply circuit low Sensor ground circuit open Transmission line pressure low Governor pressure sensor signal circuit shorted to sensor ground inside trans 5 volt supply circuit open inside trans 5 volt supply circuit shorted to ground inside trans 5 volt supply circuit shorted to sensor ground inside trans Sensor ground circuit open inside trans Governor pressure sensor Copyright � 2002 ALLDATA LLC That means you go to your local Dodge dealer, grab the Governor Pressure Solenoid, Transducer, 2 gallons of Mopar ATF, a filter, and gasket and change them out. It takes about 1 hour total to do the job in your driveway. YOU DO NOT HAVE TO REMOVE THE VALVE BODY Once the pan is dropped and the filter is removed you will notice the wiring laced threw-out the valve body. These lead to your GPS and Transducer solenoid. I didn't want to go the dealer route and pay big bucks for the Governor Pressure sensor and Governor Pressure solenoid. With a little online searching I found Transtar Industries, Inc. at www.transtarindustries.com Part numbers where 20A-120A for the sensor and 5A-303 for the solenoid. The prices quoted me were just over $120 for both parts. This was $100s better than what the dealer quoted me. This was for a 1997 46RE transmission. Also applies to the 47RE trans. MRinfinit3 Jake- ASE Master Certified Tech. 2008
Sensor can be a transducer but transducer cannot be a sensor Is it right or wrong?
It is wrong.
What is a VTEC sensor?
its not really called a vtec sensor. its a Vtec Solenoid, the solenoid has an oil pressure switch mounted on the solenoid. When the head reaches a certain pressure the oil pressure switch sends a signal to the ecu and the ecu sends a signal to the solenoid to open the extra valves
How do you install governor pressure sensor 1997 Town and Country van?
A 1997 Chrysler Town and Country does not have a governor pressure sensor.
