Your PHP setting limits the maximum file sizeÊthat could be loaded to 4 MB. You could adjust this setting to a higher value by editing your php.ini file.Ê
The initial load in Rockwell hardness test is 10KGf.
Stress testing means increasing the load ,and cheking the performance at each level. Load testing means at a time giving more load by the expectation and checking the performance at that leval. Volume testing means first we have to apply initial load,then at certain time increase the load and check the performance.
a resistive load is the same all the time, a tungsten load has an initial surge of current that's higher until the filament heats up and it's resistance increases.
maximum demand load can be calculated as: # maximum demand=demand factor * Connected load or by # maximum demand = connected load * Diversity Factor Note: Demand factor and diversity factor are NOT same
the efficiency is maximum in a transformer when no load loss is equal to load loss.
The Maximum Power Transfer Theorem is not so much a means of analysis as it is an aid to system design. The maximum amount of power will be dissipated by a load resistance when that load resistance is equal to the Thevenin/Norton resistance of the network supplying the power.
The maximum safe femur load, according to SAE is the allowable injury assessment value. The maximum femur load is 2250 lbs.
It means that you open an existing text file using an application like Notepad, Word, Excel etc.
An electricity board will be fixed some amount of load for consumer (industry or commercial) as per consumers requirement.That is maximum load or maximum demand.
you may need it if your file with the brush in is a rar file , then you need winrar to extract it otherwise you just load brush in cs3 then load the .abr file you may need it if your file with the brush in is a rar file , then you need winrar to extract it otherwise you just load brush in cs3 then load the .abr file
200 amp maximum combined.
it should just load a file on its own
The maximum load would be 100 kVA, or 33.333 kVA on each phase.
It is always desirable to run any equipment or device at maximum efficiency for that matter, not only the power transformer. Power transformer maximum efficiency occurs when copper loss is equal to iron loss. (or no load loss equals to load loss). This does not necessariliy mean that maximum efficiency occurs at maximum or full load. Generally the maximum efficiency occurs at relatively less than full load of the transformer.
maximum load the soil can withstand,is the load bearing capacity of the soil.
load in terms of any electrical machine is of 3 types mainly :- 1)resistive load--it means the load connected is a resistor only. 2)inductive load--it means the load applied is an inductor only. 3)capacitive load--it means the load is capacitor only. 4)also there may be combination of all these types or any two of the above loads like capacitive -resistive load;capacitive -inductive load. NO LOAD:--- as it is very clear from the word itself that it is no load that means no load has been applied to the machine..i.e.the output terminal of machine is open circuited FULL LOAD:-- the maximum load value that can be applied to the machine at which it can work without damaging any part of the machine is called machine working at full load ---------mrityunjay pandey (kiit university ,btech 2nd year)
The Peerless SA750P-S has a maximum load capacity of 150 pounds and is designed specifically for LCD and plasma screens measuring 32" to 50". The maximum load capacity for this mount is 150 lbs.
This rack does not have a maximum weight load listed as it is only for accessories such as jump ropes, cables and bar handles.
NO LOAD:--- as it is very clear from the word itself that it is no load that means no load has been applied to the machine..i.e.the output terminal of machine is open circuited FULL LOAD:-- the maximum load value that can be applied to the machine at which it can work without damaging any part of the machine is called machine working at full load.
An electricity board will be fixed some amount of load for consumer (industry or commercial) as per consumers requirement.That is maximum load or maximum demandAnswerA 'maximum demand indicator' (also called a 'thermal demand indicator') is a thermally-operated measuring instrument which indicates the maximum current supplied by a distribution transformer, from which that transformer's actual (rather than anticipated) maximum load can be determined. A distribution transformer is sized based on an anticipated load, resulting from an analysis of the loads to be supplied (taking into account after-diversity maximum demand), this instrument allows the actual maximum load to be compared with that calculated load, and this value should be less if the original analysis was performed correctly.
the answer is 10KGF
2.5 times of design load
This means there is a reactive component, either inductive or capacitive, to the load.