0
The terminology would typically reference a device such as a power supply, charger, diverter or transformer. The Input Voltage is the voltage supplied to the device to make it work. The Output Voltage is what the device supplies to an application.
For example, a power supply for a laptop might convert 120 VAC to a voltage like 19.5 volts (A Sony Laptop) for charging a laptop battery.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
A single phase transformer has an input voltage of 240v and output voltage of 50v and a rated input power of 4.20kW if their is 1344 windings on the input side how many on the output?
There is (240 / 1344) = 179 milli volts per turn. The output voltage is 50 volts, so 50 / .179 = 280 turns on the secondary.
Use of transistor 7812?
7812 is not a transistor. It is a three lead voltage regulator integrated circuit. Its maximum input voltage should be near 35 volts. The minimum input voltage should be near 14 volts. The output will be 12 volts.
What is the peak value of the input to a half wave rectifier if the half wave rectifier is 10V?
In this case, the peak voltage, which is half the peak to peak voltage, is 100 volts. Additionally, the half-wave rectifier will only provide an output for half the input cycle. In the case of a full wave rectifier, the RMS output voltage would be about 0.707 times the value of the peak voltage (100 volts), which would be about 70.7 volts. But with the output operating only half the time (because of the half wave rectification), the average output voltage will be half the 70.7 volts, or about 35.35 volts RMS.
What current does the input required to give an output on Lm741?
It depends on the shunt feedback resistor on the op-amp, for example with a 10k feedback resistor connecting the output to the inverting input, 1 mA input current gives 10 volts signal output. The input terminal stays near zero voltage because of the high open-loop gain of the op-amp, so the inverting input is termed a 'virtual earth'.
Can you improve voltage level in the range of millivolt into a 15volt?
A voltage amplifier (high input and output impedances) with a gain of 83.5 dB will amplify a signal of 1 millivolt to an output of 15 volts.
How many volts on a hei distributor?
Input is 12 volts. Output can be over 50,000.
What is wattage rating of microwave oven transformer also hi voltage from secondary?
The rating is about 1500W. This is for both the input and the output. Output voltage is usually 2,000 volts. Divide watts by input volts to get input current. And divide watts by output voltage to get output current. -Joe
When you have 12 coils on the output side of a transformer and 3 coils on the input side with 100 volts output what is the input voltage?
25
What happens when a regulator doesn't get enough volts?
A regulator loses some voltage in regulating its output, known as the dropout voltage. So the input voltage must be at least the output volts plus the dropout volts. If the input voltage is too low, the output will drop out of regulation.
What remains unchanged in transformer action?
In a standard transformer, the ratio of input volts to output volts remains constant.
A single phase transformer has an input voltage of 240v and output voltage of 50v and a rated input power of 4.20kW if their is 1344 windings on the input side how many on the output?
There is (240 / 1344) = 179 milli volts per turn. The output voltage is 50 volts, so 50 / .179 = 280 turns on the secondary.
How do you convert 240 volts to 1.5 volts?
There are several ways to convert a 240 volt input to a 1.5 volt output. If the 240 volt input is alternating current (AC), a simple transformer can reduce the 240 volts to 1.5 volts (AC). A properly configured resistor or impedance coil in series with the input and output would also do the job but a tansformer also serves to isolate the output from the input offering greater protection for the 1.5 volt device. You If 1.5 volts direct current (DC) is required, a rectifier circuit is needed after the 1.5 volt AC output. If the source is 240 volts (DC), A resistance circuit in series can reduce the output voltage. You can also use electronic circuitry to chop of the 1.5 volts.
What does input and output mean in maths?
The input means the problem and the output means the answer! [but not in math]
What is the output voltage of 8volts input quadrupler?
just under 32 volts, because of losses.
Is Card reader Writer input or output?
I expect you mean "Is Card reader/writer input or output?". If this is so, it is both an input and output device. Whenever you are trying to categorize a device as Input or Output, think of how it looks from the computer.If the computer is transmitting data to it, it is an Output device.If the computer is receiving data from it, it is an Input device.
A 12-bit DAC has a step size of 8 mvDetermine the full scale output voltage and percentage resolutionAlso find the output voltage for the input of 010101101101?
Assuming the zero state output of the DAC is 0 volts, then 4095 steps of 8mv would yield a full scale output of 32.76 volts. The resolution is one part in 4096, or 2.44 percent. An input of 010101101101 is 1389. Multiply that by 8mv, and you get 11.11 volts.
Is a desk a input or output?
Desktop are both, mean input and output, but in some times it is call out put device.
