0
A single phase transformer has an input voltage of 240v and output voltage of 50v and a rated input power of 4.20kW if their is 1344 windings on the input side how many on the output?
Drunknmunky91
There is (240 / 1344) = 179 milli volts per turn. The output voltage is 50 volts, so 50 / .179 = 280 turns on the secondary.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How the voltage is induced in a single phase transformer?
The changing magnetic flux in the iron core of the transformer induces a voltage in the windings.
How many windings does a single-phase transformer have?
Generally a single-phase transformer will have twowindings. One of the Low voltage side and one on the high voltage side. North-American distribution transformers will have three: one high-voltage winding, and two low-voltage windings connected in series.However......a single-phase transformer can also have several primary and several secondary windings. The primary windings can be connected in series or in parallel with each other, as can the secondary windings. For example, taking the primary winding as an example, it could consist of two 120-V rated windings: if connected in series, it could be supplied with 240 V without exceeding its voltage rating; if connected in parallel, it could be supplied with 120 V without exceeding its voltage rating. Multiwinding single-phase transformers allow for a variety of connections.
Why do you use Two Winding run and start winding in the single phase motor?
Any transformer uses a minimum of two windings to change the voltage value. The primary side of the transformer is usually connected to the existing voltage. The secondary side of the transformer is usually connected to the load, who's voltage could be higher or lower voltage than the primary voltage.If the secondary voltage is increased the transformer is known as a step up transformer and if the secondary voltage is decreased the transformer is known as a step down transformer.The transformer terminal markings for the primary are H1 and H2 on a single coil primary and H1 to H4 on a dual voltage primary winding. Like wise the secondary terminal markings are X1 and X2 on a single coil secondary and X1 to X4 on a dual voltage secondary winding.
How do you design a transformer with three phase 400v input and single phase 2000v output?
By design are you going to wind the transformer yourself? In your design you need a 5:1 ratio. On the output side of the transformer any two legs of a three phase transformer is considered single phase voltage. Good luck on your project.
What will happen if apply two phase supply to a three phase transformer?
A three phase transformer is simply three transformers so, supplying one phase to a set of three transformers will result in only one phase output. Any loads connected to that transformer that are expecting three phase power will malfunction, and could fail.AnswerA three-phase transformer is NOT 'three separate single-phase transformers', as suggested in the original answer. It is a single transformer with three primary and secondary phase-windings wound around a common three-limb ('core') or five-limb ('shell') core. If a single-phase supply was applied to one of the three primary windings, then single phase voltages would appear across each of the three secondary windings and the remaining two primary windings. These voltages would not be out of phase with each other.
How the voltage is induced in a single phase transformer?
The changing magnetic flux in the iron core of the transformer induces a voltage in the windings.
How many windings does a single-phase transformer have?
Generally a single-phase transformer will have twowindings. One of the Low voltage side and one on the high voltage side. North-American distribution transformers will have three: one high-voltage winding, and two low-voltage windings connected in series.However......a single-phase transformer can also have several primary and several secondary windings. The primary windings can be connected in series or in parallel with each other, as can the secondary windings. For example, taking the primary winding as an example, it could consist of two 120-V rated windings: if connected in series, it could be supplied with 240 V without exceeding its voltage rating; if connected in parallel, it could be supplied with 120 V without exceeding its voltage rating. Multiwinding single-phase transformers allow for a variety of connections.
Why do you use Two Winding run and start winding in the single phase motor?
Any transformer uses a minimum of two windings to change the voltage value. The primary side of the transformer is usually connected to the existing voltage. The secondary side of the transformer is usually connected to the load, who's voltage could be higher or lower voltage than the primary voltage.If the secondary voltage is increased the transformer is known as a step up transformer and if the secondary voltage is decreased the transformer is known as a step down transformer.The transformer terminal markings for the primary are H1 and H2 on a single coil primary and H1 to H4 on a dual voltage primary winding. Like wise the secondary terminal markings are X1 and X2 on a single coil secondary and X1 to X4 on a dual voltage secondary winding.
How do you design a transformer with three phase 400v input and single phase 2000v output?
By design are you going to wind the transformer yourself? In your design you need a 5:1 ratio. On the output side of the transformer any two legs of a three phase transformer is considered single phase voltage. Good luck on your project.
What is kva rating of single phase transformer?
This is the rated output of the transformer, obtained by multiplying the rated secondary voltage by the rated secondary current. And it's 'kV.A', not 'kva'.
How many winding should be there to generate 240 volts on 1500 rpm?
Generator output voltage is determined by the number of windings, strength of magnetic flux and the speed the flux crosses the windings. With the flux and windings remaining the same, a larger unit will have higher voltage than a smaller one. There is no single answer to this question.
What will happen if apply two phase supply to a three phase transformer?
A three phase transformer is simply three transformers so, supplying one phase to a set of three transformers will result in only one phase output. Any loads connected to that transformer that are expecting three phase power will malfunction, and could fail.AnswerA three-phase transformer is NOT 'three separate single-phase transformers', as suggested in the original answer. It is a single transformer with three primary and secondary phase-windings wound around a common three-limb ('core') or five-limb ('shell') core. If a single-phase supply was applied to one of the three primary windings, then single phase voltages would appear across each of the three secondary windings and the remaining two primary windings. These voltages would not be out of phase with each other.
What is a single phase variac?
It is a variable autotransformer, a transformer with a sliding contact on the winding connected to a control knob, that allows the output voltage to be varied.
What is the use of single phase variac in circuits?
A variac a variable auto-transformer, allowing the output voltage to be adjusted from zero up to a maximum voltage, which might be 20% greater than the supply voltage.
What is the procedure to polarity test a 3 phase transformer?
A 'polarity test' is conducted on a single-phase transformer, not a three-phase transformer (or transformer bank). The polarity of a single-phase transformer being important if two transformers are to be connected in parallel, or three transformers are going to be connected to form a three-phase transformer bank.'Angular displacement' is, to a three-phase transformer, what 'polarity' is to a single-phase transformer. So you really should be asking about angular displacement, rather than polarity. Angular displacement, or 'phase displacement', is the angle by which the secondary line voltage lags the primary line voltage.Angular displacement can be determined either by drawing a phasor diagram of the three-phase connection and measuring it, or by looking up the connection in a vector-group chart/table -you would nor normally 'calculate' angular displacement.
What is transformation ratio of step-up transformer?
The ratio depends on the ratio of the length of the windings and depends on the specific transformer. There is no single answer to this question.
Load test on single phase transformer?
The dc tests that can be done on a transformer are to measure the resistance of each windings and to measure the insulation resistance between the windings and between each winding and the transformer case.
