0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What alteration would occur if a single pole switch is reconnected to become a master switch?
If a single pole switch is wired to be a master switch, the switch would have to be in the on position for any other control devices to operate. Turning the master switch off would eliminate power to all devices (and/or loads) which it was serving. For example, some homes have a switch to control their outside light. If the outside light has a photo eye (the light will only come on at night), the switch is the master switch. Another example would be the breakers in an electrical panel. Each breaker would be the "master switch" for the circuit it protects. The main breaker in the panel would be the "master switch" for the entire home.
What energy changes take place when a light switch is turned on?
mechanical to electrical to light energy
What is the definition of main switch?
Type your answer here... main switch is difine as the switch which opparate whole power throw the house.
What is a electrically activated switch?
This is a switch that can be changed by applying power to a terminal of the switch (such as a key card access controlled door lock), as apposed to a switch that requires an outside force to change the position (such as a standard light switch).Additional AnswerA relay and a contactor are each examples of an 'electrically-operated switch'. Each operates on a similar principle. An 'operating coil' is used to energise or to de-energise a magnetic-operated mechanism which then either opens or closes the main contacts of the device. The operating coil may be controlled by a relatively-low voltage circuit, while the main contacts control a higher-voltage circuit.Relays tend to make/break light-current circuits, whereas contactors tend to make/break heavy-current circuits (e.g. motors).
What is meant by main contact and auxiliary contact in magnetic contactor?
The main contact controls the load current to the motor, whereas the auxiliary contact is part of the control circuit -usually connected in parallel with the 'on' pushbutton switch to maintain the control circuit in the energised state, once the on pushbutton has been pressed.
Where do you locate the main light control switch located on a 1989 Dakota?
You can locate the main light control switch located on a 1989 Dakota by looking at the user manual.
Why wont the dome lights work on your 2010 expedition?
The main dome light control switch is turned off.
Where is the rear fog light switch on the polo?
With main switch light just pull
Dodge interior lights stay on when you close the door?
You may have the main switch turned on for the light. If the main switch is on, closing the door will not result in the light going off.
What alteration would occur if a single pole switch is reconnected to become a master switch?
If a single pole switch is wired to be a master switch, the switch would have to be in the on position for any other control devices to operate. Turning the master switch off would eliminate power to all devices (and/or loads) which it was serving. For example, some homes have a switch to control their outside light. If the outside light has a photo eye (the light will only come on at night), the switch is the master switch. Another example would be the breakers in an electrical panel. Each breaker would be the "master switch" for the circuit it protects. The main breaker in the panel would be the "master switch" for the entire home.
What are the advantages of installing light timers?
The main advantage of installing light timers is that the householder can control exactly when the lights switch on and off. Not only does this act as an excellent security measure, it also has the potential to save electricity.
What Main bearing on a light vehicle engine are normally used?
Main bearings are what the crankshaft rotates on.
Where is brake light switch on 92 Lumina Z34?
Above the brake pedal. If your main brake lights dont work but your third center brake light does, then the brake light switch is not the problem. Its is the turn signal switch.
How do you change a peugeot 307 brake light switch?
In order to change the brake light switch in a Peugeot 307, you must dismantle and access the main light board on the dash and find the connecting switch, thusly flipping it back to the on position.
Where is ECM fuse?
The ECM fuse is located inside the engine of the vehicle. Engine Control Module acts as the main fuse of the vehicle.
How can you switch off the sound for Miniclip?
Most games have individual sound control at their main menu. You can also switch off the sound on your speakers.
What is the main usage of an Exide battery?
Exide is the main producer, distributors, and recyclers of lead acid batteries mainly for vehicle use. Owners of vehicles will often visit an Exide store to switch their vehicle battery.
