answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered
2014-08-02 02:52:49
2014-08-02 02:52:49

The 2.7L out of a Chrysler Sebring or Dodge Stratus.

The 2.7L out of a Chrysler Sebring or Dodge Stratus.

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

User Avatar
Wiki User
Answered
2014-08-02 02:52:49
2014-08-02 02:52:49

The 2.7L out of a Chrysler Sebring or Dodge Stratus.

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


There are four mounts on a Chrysler Sebring.There are four mounts on a Chrysler Sebring.


It mounts to the top rear of the transmission bell housing.


It has four total mounts.It has four total mounts.


There are four mounts. Center left, right, front, and rear.


On the bracket the brake pedal mounts to.


There are four, front, back, left, and right.


The 1997 Chrysler Sebring transmission is equipped with two transmission mounts. There will be a transmission mount at the back of the transmission, on each side.


4g63, you will need a new trans, engine wire harness, all accessories, like ac compressor, and alternator, and ecm. and engine mounts...fits perfectly. or you could use a v6 from an avenger or sebring.


The crankshaft position sensor mounts to the top rear of the transmission bell housing.



There are four engine mounts, one in the front, back, left and right. A real pain, unless you remove the engine to install.


You can fit a 1.8 liter engine into your 1987 Acura Integra. You will need to modify the engine mounts and the wiring harness.


b18c1, b18a1,b16 with custom or hasport motor mounts and the engine harness


The alternator on a Chrysler 300m can be replaced by disconnecting the battery, removing the wiring harness from the alternator, and then unbolting it from the mounts. The drive belt can then be slipped off and a new alternator put into place.


There is one on the left, one on the right, and one under the rear of the transmission.


You can put an engine, from your Toyota Celica, into your Toyota Corolla. The wiring harness and the motor mounts will need to be changed.


The 1995 Dodge Neon engine mounts are located on each corner of the engine. There will be to engine mounts in the front and two engine mounts in the rear.


A big block Chrysler (Dodge) 440, or even a Hemi would bolt in, with the appropriate engine mounts.


yes, but you will have to buy mounts, transmission, linkage, axles, ecu and front spindles, you will have to change your wiring harness and go backwards to an obd1 harness, or use a jumper harness.


You can swap the engine from your 1997 Cavalier 2.2 liter engine to your 2000 Chevy Cavalier. The wiring harness and motor mounts should be in exactly the same.


With the correct computer, wiring harness, mounts, attachments, etc.


yes, it can work however your going to need the engine, transmission, ecu, wiring harness, and bcm, and someone who knows how to fabricate new engine mounts and trans mounts, its quite a costly engine swap, but with lots of money and time just about anything can be done


The B20a engine available in a CR-V can be transferred into a Honda Civic. The Civic will require special mounts, harness, and computer to accommodate the larger engine.


Not without serious mods. For example coumputer, motor mounts, and wiring harness.


Check the engine and transmission mounts along with the exhaust hangers.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.