0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why cant the coarse adjustment knob be used on high power lenses?
The coarse adjustment knob is used for making major changes to the focus, and is therefore too inaccurate to use at high powers, where only a very fine adjustment can drastically change the clarity of the picture you see.
Which knob is used to get a clear image on a microscope?
You use the Fine Adjustment Knob to give a very clear image on the microscope, mostly used on high power magnification.
What is fine adjustment of the microscope?
You use the fine adjustment to focus in HIGH power with a compound microscpe.
What is the use of the focusing knob on a microscope?
The answer is in the name. To focus the material or substance for a better/clearer view.
Why would you never use the coarse adjustment knob on high power?
The coarse adjustment knob may move the lens too far too fast and the slide may crack and/or the object be squashed. Using the fine adjustment lens will bring the object into focus much more accurately. In addition, the coarse adjustment knob adjusts in too great a quantity. The fine is less responsive so its easier to adjust at high magnification.
Which focusing knob do you never use under high power?
The coarse adjustment knob should never be used when viewing in high power with a compound microscope. When in high power, use the coarse adjustment (the knob smaller than the coarse adj.) to more accurately focus on the subject.
When do you use fine focus and the coarse focus knobs?
The fine focus knob is used to bring an object into fine focus, while the course focus knob is used to bring an object into approximate focus. The course focus knob should only be used on the low-power and scanning objectives of the light microscope. Using it on the high power microscope is okay, but you should be very careful. It is no recommended to use the course adjustment knob on the oil-emersion objective as it is so close to the stage and could lead to a potential break in the slide. Fine focus adjustment knob is useful to bring out the fine details in the specimen on your slide. Can be used on any of the objectives, but most receptive on the high-power and oil-emersion objectives.
What is the correct microscope procedures?
Which of the following is a correct procedure for the operation of a microscope? First, put the specimen into focus using a low power lens, then switch to a lower power lens if needed.Remove and add slides while the high power lens is selected.First, put the specimen into focus using a low power lens, then switch to a higher power lens if needed.Use the fine focus knob with the low power lens and use the coarse focus knob with the high power lens
When using the high power objective which focus knob do you use?
The fine adjustment knob is used with the power objective on the microscope. Since the objective is already at the highest objective possible for that microscope, using the coarse adjustment knob would focus to much on the object making the details harder to read. Using the fine adjustment knob, you are able to see the fine details within the object or organism you are studying. The higher the power, the finer the knob and the lower the objective, the coarser the knob and objective.
Which focus knob should you use first when looking at a specimen?
You MUST use the coarse focus knob.
Why shouldn't you use the course adjustment knob when viewing the specimen under high power?
You shouldn't. You can cause the high objective to smash into the surface of the slide and crack it. Always use the fine adj. for high power and if you cannot get the high power in focus, reverse out to low again and do it over. Ideally, if you are in focus on low, you should be in focus at medium (may have to adjust a small amount) and if you are in focus under medium, when you swing the high power obj. into place, it should be in focus as well (may need a fine tune). Always reverse out and start all over again if you cannot focus it under high power. Deja Was Here
When focusing the object under low power which focus knob do you use first?
Either Fine or Coarse adjustment.
What part of the microscope should you used to focus the image when using high power objective lens?
First of all, one should never call it high power, it is morecommonly called the "high objective", yet that is not what this question is asking. To answer the question: You use the fine adjustment knob. This knob should be located near the coarse adjustment knob, on the opposite side of the microscope (at the same height as the coarse adjustment knob), or even as a separate knob protruding from the coarse adjustment knob. The fine adjustment knob is smaller in size. You should never, ever use the coarse adjustment knob under the high objective, you could scratch the microscope slide, cover slip, high objective lens, or in a worst case scenario break the high objective lens.
Why cant the coarse adjustment knob be used on high power lenses?
The coarse adjustment knob is used for making major changes to the focus, and is therefore too inaccurate to use at high powers, where only a very fine adjustment can drastically change the clarity of the picture you see.
What are the dangers of high power objective?
The field for the high power objective is very small, so if you do not have the organism or whatever you want to view in focus on a lower power, it may be very difficult to find on high power. Also, the lens for the higher power objectives are longer than the lower ones, which makes them closer physically to the slide that you are viewing than the lower objectives. Thus you must use the fine tuning knob to sharpen the image in high power, because you could break the slide if you use the course adjustment knob.
What is the adjustment knob on a microscope?
The course adjustment knob raises and lowers the stage of the microscope. This knob is mainly used on the scanning and low power knob to simply find the specimen. When trying to focus directly, use the fine adjustment knob.
What is the name of the adjustment knob that moves the body tube for focusing with the high-power objective lens?
I assume you would use the fine adjustment knob for high power objectives.
