0
What has the highest output voltage because of the lower voltage drop between peaks?
Wiki User
∙ 11y ago
A halfe-wave rectifier
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the effect of diode voltage drop as the output voltage?
The effect of diode voltage drop as the output voltage is that the input voltage will not be totally transferred to the output because power loss in the diode . The output voltage will then be given by: vout=(vin)-(the diode voltage drop).
What is the off load voltage of the generator?
Terminal voltage is the voltage between the output terminals of a generator.
Difference between linear IC and Digital IC?
In linear IC'S the output voltage is very according to input voltage In digital IC's the output voltage is either high or low
Why might the unloaded output voltage of a transformer be higher than its rms of 12.6v?
Because the windings of transformers have resistance, the primary and secondary currents will cause voltage drops. To compensate for the drops, the transformer may have been designed to have a higher than specified output voltage when there is little or no output current. The no load output voltage typically is only slightly greater than the specified voltage. Before measuring the output voltage, measure the input (line) voltage. If it is not as specified for the transformer, calculate its effect on the output.
The output voltage between phases of ac 3 phase supply is 240V?
No, this voltage appears ACROSS individual phases, or BETWEEN a line conductor and the neutral
What is the effect of diode voltage drop as the output voltage?
The effect of diode voltage drop as the output voltage is that the input voltage will not be totally transferred to the output because power loss in the diode . The output voltage will then be given by: vout=(vin)-(the diode voltage drop).
What is the off load voltage of the generator?
Terminal voltage is the voltage between the output terminals of a generator.
Can you say which bridge rectifier voltage has the highest out put voltage?
A: NO the power output will be higher. Bridge rectifiers do not provide more voltage output it just add more power by rectifying both positive and negative voltage of the AC input
What is residual voltage in lvdt?
Output voltage at the null position is ideally zero. But because of harmonics in the excitation voltage and stray capacitance coupling between primary and secondary usually some nonzero voltage exists at null voltage. This is called residual voltage. If it is less than 1 % of full scale output voltage ( which is the normal case) it is in the acceptable limits.
Difference between linear IC and Digital IC?
In linear IC'S the output voltage is very according to input voltage In digital IC's the output voltage is either high or low
What is difference between stabilizer and voltage regulator?
A voltage regulator is a circuit or device designed to deliver a constant voltage at its output regardless of changes in load current.A voltage stabilizer is a circuit or device designed to deliver a constant voltage at its output regardless of changes in incoming voltage.
What is the Difference between linear IC and digital IC?
Both linear ICs and nonlinear ICs has an output voltage which is dependent on the input voltage. However, the difference is that linear ICs produce an output voltage which increases or decreases at a "fixed rate" relative to the input voltage. Nonlinear ICs do not do this. A voltage regulator may be considered nonlinear because as you increase the input voltage the output will climb at the same rate (just like linear ICs), however, once the input voltage reaches a particular level point, the output no longer increases as you increase the input. This is at the point where regulation begins. The nonlinear IC no longer changes its output at a fixed rate relative to the input.
Why might the unloaded output voltage of a transformer be higher than its rms of 12.6v?
Because the windings of transformers have resistance, the primary and secondary currents will cause voltage drops. To compensate for the drops, the transformer may have been designed to have a higher than specified output voltage when there is little or no output current. The no load output voltage typically is only slightly greater than the specified voltage. Before measuring the output voltage, measure the input (line) voltage. If it is not as specified for the transformer, calculate its effect on the output.
Difference between csi vsi and zsi?
vsi's output voltage is independent of load nature, but output current is depends on load nature. csi's output current is independent of load nature, but output voltage is depends on load nature.
What is an output voltage swing?
Output voltage swing is defined as the maximum positive or negative peak output voltage that can be obtained without wave form clipping, when quiescent DC output voltage is zero. VOM is limited by the output impedance of the amplifier, the saturation voltage of the output transistors, and the power supply voltages. This is depicted in the figure above. This emitter follower structure cannot drive the output voltage to either rail. Rail-to-rail output op amps use a common emitter (bipolar) or common source (CMOS) output stage. With these structures, the output voltage swing is only limited by the saturation voltage (bipolar) or the on resistance (CMOS) of the output transistors, and the load being driven.Maximum and minimum output voltage is usually a design issue when dynamic range is lost if the op amp cannot drive to the rails. This is the case in single supply systems where the op amp is used to drive the input of an ADC, which is configured for full scale input voltage between ground and the positive rail. Because newer products are focused on single supply operation, datasheets use the terminology VOH and VOL to specify the maximum and minimum output voltage.
Can Voltage dividers can provide only positive output voltages?
Voltage dividers can provide anything between VCC (the most positive voltage in the circuit) and VSS (the most negative voltage in the circuit). For example, if VCC =0 and VSS = -15, then the output voltage has to be negative. ========================
Why is a Schmitt trigger called a regenerative comparator?
A Schmitt Trigger is a comparator, because it compares its input voltage to a "threshold" voltage, but it has _two_ threshold voltages (the upper and lower trigger voltages), and which threshold voltage is used depends on the output state. If the input voltage is higher than the upper trigger voltage, the output will be high (for a non-inverting Schmitt trigger). In this state, the input is compared to the lower threshold voltage, so the input now has to go below the lower threshold voltage before the output will go low. The threshold voltage depends on the output state, such that a high output selects the lower threshold voltage, and a low output selects the upper threshold voltage. This can be visualised as using a fixed threshold but adding a small voltage (the difference between the upper and lower threshold voltages, also called the hysteresis voltage) to the input voltage before it is compared. This small added voltage is high when the output is high, and low when the output is low. A small amount of the output voltage is effectively being added to the input voltage before it is compared to a fixed threshold. This is positive feedback, also called regenerative feedback. So a Schmitt trigger operates as a voltage comparator, and a small amount of the output is added to the input, so it uses positive or regenerative feedback.
