What if resetting the back up sensor does not work on a 2002 ford ford explorer?
The 2002 Silverado 4.8 liter engine knock sensor is located on the back of the crankshaft. The back engine cover will need to be removed in order to view the sensor.
The 2002 Mitsubishi Gallant speed sensor is located on the back of the transmission. The speed sensor will be in the right-hand corner of the transmission.
it is located under the back seat under the carpetType your answer here...
On the back of the alternator
The 2002 Toyota Tacoma 3.4 liter engine IAT sensor is located on the outside of the air cleaner housing. The sensor is on the back of the housing.
I believe the DPFE sensor is at the back of the 5.0 L by the throttle body
the speed sensor is located in the back of the transmission in between the axles
The 2002 Chevy Cavalier 02 sensor can be found attached to the air cleaner housing. The O2 sensor will be on the back side of the air cleaner housing.
The 2002 Ford Ranger camshaft position sensor is located on the back of the camshaft. The rear engine plate will need to be removed in order to view the sensor.
In the back of the engine.
abs is kicking in ..more than likely a wheel speed sensor
You have to have the factory do it, or a locksmith. (thats for resetting the remotes and codes) if you just want to reset it then unplug the battery for 10 mins then hook it back up
The 2002 Lincoln LS mass airflow sensor can be found on the air cleaner housing. The mass airflow sensor will be on the back side of the air cleaner housing.
remove the door panel
hire a dectective
Usually, it is located on the very back, top of the engine, near where the engine and transmission bolt together. There is no knock sensor.
It is on the back exhaust manifold.
4.3L, on back of engine, on top, drivers side.
There are two in the exhaust on the back side of the engine.
It is the sensor that is screwed into the exhaust manifold on the back of the engine.
I just got these fixed. There is a forward (primary) sensor and a back (secondary) sensor in front and back of the catalayic converter within the muffler.
Why does the timing retard itself when the engine is accelerated after putting the cams back in and resetting the timing on a 1992 Geo Prizm LSI?
if you unplug the knock sensor and run it and it clears up then change the knock sensor if it doesn't check cam caps for torque specs and lifters if it set up for awhile
It's at the top of the transmission on the back corner.
Recently I had the DPFE Sensor (as opposed to "switch") replaced in my 2002 Ford Explorer Limited. This sensor "as per FSA 02M01" was replaced because my "service engine soon" showed up in the message board display. Following this new sensor installation, my transmission is now defunct and sits in a Ford dealership waiting for replacement of "cellinoids" (solenoids?). This is what I have been told, I hope this is helpful to you. I'm not… Read More
Why does my ford explorer 5.0 8cyl camshaft sensor act up when i unplug the sensor it runs great when i plug it back in the truck acts up and feel like its going to stall out?
pcm is going into default mode you likely have a bad cam sensor
Where is the oil pressure sensor and the temperature sensor located on a 2002 dodge ram 1500 magnum V8?
OIL PRESSURE SENSOR IS LOCATED IN BACK OF ENGINE ON TOP UNDER WINDSHIELD WIPER PANEL
usually its in the air box, with 2 wires out the back Not Accurate On a 2002 Hyundai Accent the IAT is bundled with the MAF sensor located on the throttle body. However, which wires are which I'm not sure. Not Precise The 2002 Hyundai Accent 1.6 DOHC doesn't have a MAF sensor! 2002 1.6 DOHC has the IAT integrated into the Manifold Absolute Pressure (MAP) sensor. 2002 1.5 SOHC has the IAT integrated to… Read More
Bank one on your vehicle is on the back side of the vehicle. Sensor 1 is the first sensor coming from the engine in the exhaust, the one before the catalytic convertor.
On Back of the Engine
Back of the engine, in the exhaust above the catalytic converter.
Bank 1 sensor 1 is screwed into the exhaust manifold on the back of the engine. Bank 1 sensor 2 is screwed into the catalytic converter. Bank 1 sensor 1 is screwed into the exhaust manifold on the back of the engine. Bank 1 sensor 2 is screwed into the catalytic converter.
Back up sensor 2003 ford explorer turns itself off after shifting into reverse How do you determine which of the four sensors is bad?
I don't have an answer but I have exactly the same problem!!
it is bolted on the back of the engine ( on the alluminum part that says 5.0 ).. It has 2 bolts and 2 vacuum lines connected to it.
Where is the coolant temperature sensor located on a 2002 Nissan Sentra? my car s dashboard gauge shows my car is running hot the drops back down to normal any idea? [Improve]
Check the back of your rear view mirror.
At the back of the engine on the coolant outlet that goes to the heater hoses on the firewall.
on the right side of block about mid way up and back
Inside the distributer cap on the back side of it.
should be the same reservoir as the front windshield wipers
Where is the location of the bank one oxygen sensor on a 2002 chrysler town and country mini van with a 3.8 liter?
Bank one sensor one is in the exhaust manifold on the back of the engine before the catalytic converter. Sensor two is screwed into the side of the converter.
On the 4.0 L OHV engine , the camshaft sensor is at the back of the engine,on top of the engine block, where the distributor used to be installed on the older versions. According to my Haynes repair manual.
I have the same engine in my 1995 Ford EXPLORER : I can't see the camshaft position sensor but from what I have read it is on the top of the engine , near the center line , at the back of the engine near the firewall
It is on the back of the engine, next to the distributor.
http://site.oemdirectsolutions.com/ offers a painted to match panel for $229.
if it is the 4.0 look on passenger side back of the engine at the top almost need a flashlight and mirror i had to undo wiring harness to get to it and change
By resetting your account.
The camshaft position sensor on a 4.3L engine is inside the distributor near the rear of the engine. Has the intake manifold gasket been replaced? Sometimes it is overlooked to plug the sensor back in after this repair has been done.
Not all Explorer engines had an EGR valve. If you have a 4.0, and it has an EGR, look on the driver's side of the engine, mounted to the upper intake manifold. It will be an aluminum colored metal or black plastic sensor, with one electrical connector and two hoses going to it. If you have a 5.0, it will be at the rear of the engine, mounted on the back of the throttle body.
It is on the top back right side of the intake manifold. with you standing in the front of engine.