0
What else can I help you with?
You want to run power from your home you have a 200 amp in the house to a garage that you recently built you have 110 and 220 outlets The only 220 you plan on running is a small air compressor What?
The voltage for the air compressor is needs to come from a double (two) pole breaker. The size of the breaker needs to be 250% of the full load amps of the compressor. The wire size to the compressor has to be 125% of the full load amps of the compressor.
How many amps in 3 AA batterys?
3 AA batteries provide about 4.5 volts. The amps depend on the load but for D-cells a load of 10 amps can be sustained for short periods.
What is type of breaker for 41 amp's?
For a 41 amp load, you would typically use a 50 amp circuit breaker. The general rule is to select a breaker size that is 125% of the continuous load amps or equal to the load amps if it is not a continuous load. In this case, 41 amps is considered a continuous load, so you would round up to the nearest available breaker size, which is 50 amps.
Does 1000va equal 10 amps?
No, 1000VA does not necessarily equal 10 amps. The relationship between VA (volt-amperes) and amps depends on the power factor of the load. For a purely resistive load (like an incandescent light bulb), 1000VA at 120V would be equivalent to approximately 8.3 amps.
What is FLA in electrical terms?
FLA = full load amps <<>> It is a term that is associated with motors. It is the amperage of the motor when it operates at its full rated horsepower under load.
What instrument is used to check the full load amps of a compressor?
amprobe
How do you tell if the compressor is bad in a window air conditioner?
Borrow a clamp on amp meter and check full load amps. If pulling full load amps then compressor condemned.
What does rla mean on an air compressor?
Rated load amps = rla
You want to run power from your home you have a 200 amp in the house to a garage that you recently built you have 110 and 220 outlets The only 220 you plan on running is a small air compressor What?
The voltage for the air compressor is needs to come from a double (two) pole breaker. The size of the breaker needs to be 250% of the full load amps of the compressor. The wire size to the compressor has to be 125% of the full load amps of the compressor.
What is the difference between full load amps and running load amps?
Full load amps is the maximum rated amps that the motor should draw according to its nameplate rating. Running load amps is the actual amperage the motor is drawing at that point in time when the test is taken. Some motor loads vary depending on if the load is cyclic. The reading on this type of motor would be from no load amps to full load amps.
What is the demand load in amps for a range with a 2.4kW single phase at 220V?
That load would be 10.9 amps.
What is the maximum current rating for the circuit breaker that can handle a load of 40 amps?
The maximum current rating for the circuit breaker that can handle a load of 40 amps is 40 amps.
What is the full load amps for 2.4 hp motor at 460 volts?
what is the full load amps for 2.4 hp motor at 460 volts ?
How much full load ampere in 2 horse power compressor?
It depends on the voltage of the compressor. Two horse power (electric) is 1492 watts, but watts are volts times amps, so you need to know the voltage. Since the motor is an inductive load, you will also need to know the power factor, so as to compensate for true vs apparent power.
How many amps in 3 AA batterys?
3 AA batteries provide about 4.5 volts. The amps depend on the load but for D-cells a load of 10 amps can be sustained for short periods.
Why is my single phase induction motor drawing to many amps?
I have a single phase induction motor. It draws 8 amps on start up and climbs to 14-15 amps when I put a load on it. When I don't have a load it runs at 1 and climbs to 2-3 amps. It is normal operation for this motor to run at the lower number of amps with a load. But I don't know what is wrong.
What is type of breaker for 41 amp's?
For a 41 amp load, you would typically use a 50 amp circuit breaker. The general rule is to select a breaker size that is 125% of the continuous load amps or equal to the load amps if it is not a continuous load. In this case, 41 amps is considered a continuous load, so you would round up to the nearest available breaker size, which is 50 amps.
