0
What else can I help you with?
A device or circuit that provides power to the rest of the circuit or system is called what?
A device or circuit that provides power to the rest of the circuit or system is called a power supply,
What do you use fuses in?
Electrical circuits, to limit the maximum current flow. Fuses will "blow", or burn out, and cause an open circuit, to stop the flow of current when it could potentially damage a circuit, system, or device.
Does the grounded conductor have normal circit current flow?
Yes, the grounded conductor carries normal circuit current flow in a typical electrical system. It provides a return path for current back to the source, completing the circuit.
In an electric circuit the ground prevents current from flowing in the circuit true or false?
In an electric circuit, the ground does not prevent current from flowing. Instead, it provides a safe path for electrical current to return to the earth in the event of a fault. It's a protective measure to prevent electrical shock hazards by maintaining the voltage stability in the circuit. The normal operation of the circuit isn't affected by the grounding system.
What is a device consisting of a thin wire that melts to break a circuit?
A device consisting of a thin wire that melts to break circuit is a fuse. Once an outlet is giving out more electricity than its used to it melts which stops the current from flowing. The best thing to do if that happens is unplug the devices in the outlet and put in a new fuse
What body system is similar to an electrical circuit?
The nervous system is similar to an electrical circuit in that it transmits electrical signals (nerve impulses) throughout the body to communicate and control various functions. Just like how an electrical circuit carries current to power a device, the nervous system carries impulses to coordinate body movements and regulate bodily processes.
What is an analogous safety device in an electric circuit corresponding a shear pin in a mechanical system?
A fuse or circuit breaker
Why is the earthing system drawing current?
There is a short circuit somewhere in the electrical system.
What is the relation between surge current and fault current?
Fault/short circuit current is the available current from the source when a short circuit occurs. It is the maximum current the source can provide, defined as an RMS value, usually without any DC offset. Surge current is the maximum instantaneous current that is drawn by "turning on" or energizing a device such as a motor or transformer. Surge current will be less than fault current. If you assume a very strong source relative to the device rating, the surge current will be solely dependent upon the device in question (so fault current and surge current have no intrinsic connection). For a transformer, inrush may be 5-7 times the self cooled full load rating. Motors are usually less than this, and depending on the starting technique and configuration can be little (20-50%) over full load rating. From these definitions, and the above paragraph, it should be clear that if you have a weak source relative to the device, the device may not be able to draw as much current as it would if connected to a stronger system. If this occurs, the voltage will dip. An example would be a system where the available short circuit power is 600MVA; A 60MVA transformer is connected to this system bus. Energizing this transformer without any sort of controled closing could result in (7) x 60MVA = ~420MVA on inrush. This is relatively close to the available short circuit power (70%), so you can expect the system voltage to dip as a result. If the available short circuit current was around 20,000MVA, energizing such a transformer would not cause any significant system voltage dip.
What is the difference between a fuse and circuit?
A fuse is a safety device that breaks a circuit when current exceeds a certain level, protecting the circuit from overheating and potential damage. A circuit is a path that allows electricity to flow, connecting components like switches, resistors, and capacitors to create a functional electrical system.
What electrical safety device has a piece of metal that melts when a current becomes too strong?
A fuse is an electrical safety device that contains a piece of metal that melts when the current flowing through it becomes too strong. This melting of the metal breaks the circuit and prevents overheating of the electrical system.
What mean Frame Ground?
The frame of a device is usually the supporting structure that holds the electrical device. The electrical code requires that the frame of any electrical device be brought down to ground potential. This is done with a ground wire taken from the frame of the device and connected to the service distribution ground. This is also classed as a bond wire. Now if a fault current occurs any where in the bonded system, the fault current will travel back to the distribution panel and trip the circuit breaker of the faulted circuit removing the voltage from the faulted circuit..
