0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you wire one light and one GFCI and another light light and fan with two switches and one power line?
Connect the incoming power to the line side of the GFCi outlet. Now run another wire connected to the line side of the GFCI outlet from the GFCI outlet to the switches. Power one of the switches and use that switch to turn on the 2 lights. Run power from that switch to another switch and use that switch to send power to the fan. Mount both switches in a double pole switch box. If the light above the sink has an outlet on it then you will have to connect power going to that light on the load side of the GFCI outlet. If not then just connect it to the line side.
The gfci indicator light is on but appliances connected to the gfci outlet are still powered what is causing this?
The last answer is incorrect. Some GFCI's are designed to light up when working, some are designed to light up when tripped, some are designed to have different color lights depending on normal or tripped conditions. The only way to tell if the receptacle has power is to TEST it. If the GFCI is supposed to be tripped and power is still available, it is either not operating properly or it is not wired properly. If in doubt, have an electrician inspect it for proper operation. Incorrect answer: >>Provided that the GFCI is wired correctly, the indicator light indicates that the receptacles have power. If the light is off there is a ground fault. In other words, the light should always be on.
If the test switch is bad on a gfci will the breaker still work?
If the test switch is faulty then there is no convenient way to determine if the GFCI is functioning, and technically, if the test switch is faulty, then as it is a part of the GFCI, the GFCI is faulty and should be replaced.
How do you wire dual switch-plug gfci which has extra wires?
there should be 5 wires, hot and switched hot for the switch and hot, neutral and ground for the gfci receptacle.
Add new gfci from an existing switch?
Find the Hot side of the switch (Where there is voltage regardless of position of toggle on switch). Tie in new Black wire to GFCI. On wire nut with white wire tie in new white wire to GFCI. Do the same for the bare ground wire, if there is one.
How do you wire one light and one GFCI and another light light and fan with two switches and one power line?
Connect the incoming power to the line side of the GFCi outlet. Now run another wire connected to the line side of the GFCI outlet from the GFCI outlet to the switches. Power one of the switches and use that switch to turn on the 2 lights. Run power from that switch to another switch and use that switch to send power to the fan. Mount both switches in a double pole switch box. If the light above the sink has an outlet on it then you will have to connect power going to that light on the load side of the GFCI outlet. If not then just connect it to the line side.
The gfci indicator light is on but appliances connected to the gfci outlet are still powered what is causing this?
The last answer is incorrect. Some GFCI's are designed to light up when working, some are designed to light up when tripped, some are designed to have different color lights depending on normal or tripped conditions. The only way to tell if the receptacle has power is to TEST it. If the GFCI is supposed to be tripped and power is still available, it is either not operating properly or it is not wired properly. If in doubt, have an electrician inspect it for proper operation. Incorrect answer: >>Provided that the GFCI is wired correctly, the indicator light indicates that the receptacles have power. If the light is off there is a ground fault. In other words, the light should always be on.
If the test switch is bad on a gfci will the breaker still work?
If the test switch is faulty then there is no convenient way to determine if the GFCI is functioning, and technically, if the test switch is faulty, then as it is a part of the GFCI, the GFCI is faulty and should be replaced.
How do you install a GFCI so it is always on to a two way light switch that controls a vent and a light in a bathroom?
Your question sounds simple but it isn't. There are two ways of wiring a light to a switch. One is to bring the hot and neutral wire to the switch box and from there run wires from the switch to the light. If this is the case you can install a GFCI on the circuit. The other way is to bring the hot and neutral wire to the light and from there run two wires to the switch and switch the light that way. In this case you cannot install a GFCI to in the switch box. <<>> The way you want the circuit to work has to be laid out as follows. Method one, the circuit that now controls the bathroom devices can be changed to a GFCI breaker. This is probably the quickest and cheapest, unless the job is new construction. Method two, if new construction use this method, as tearing walls open to get to the wiring will become costly. Where a supply circuit comes from the service distribution panel the first device on that circuit has to be a GFCI receptacle. This device has secondary terminals on it, that if connected every device downstream from it will also be protected. So if you supply the two way light switch that controls the vent fan and a bathroom light from the secondary terminals from the GFCI receptacle they will be protected.
Where is the indicator relay situated on a 1995 Ford Fiesta?
its pluged in to the wiper, light,indicator switch assembly.
Where is the indicator relay situated on 1995 Ford Fiesta?
its pluged in to the wiper, light,indicator switch assembly.
How do you change indicator relay on a passat?
My data is showing the indicator relay as being part of the hazard light switch.
How do you wire a spst 12 volt 3 pin toggle switch with a indicator light?
Without an indication of what you want the indicator light to do, this question can not be answered.
Could you show me an electrical drawing of a circuit with GFCI protecting a switch?
GFCI's are not used to protect a switch they are used to protect an outlet where something is plugged in.
Does a 2001 doge neon have a low oil switch?
It has an oil pressure switch whose only purpose is to turn an indicator light on if the oil pressure is too low. The switch is located on the back of the block.It has an oil pressure switch whose only purpose is to turn an indicator light on if the oil pressure is too low. The switch is located on the back of the block.
How do you wire dual switch-plug gfci which has extra wires?
there should be 5 wires, hot and switched hot for the switch and hot, neutral and ground for the gfci receptacle.
How do you replace the back-light bulb in the headlight switch of a 2001 Dodge Durango?
Pull the switch and change bulb in rear. 1 for night light and 2nd for fog light indicator.
