0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How to conect a subwoofer?
You can connect a subwoofer to a computer or your TV by using its jack pin.
What is the RJ11 jack used for?
The RJ11 Jack, also known as a Registered jack, is used to connect electronic equipment to a local telecommunications service. The RJ11 jack is usually plugged into a six-pin 6P6C jack.
Is headphone jack pin popular in USA?
It's universal. Most smartphones have it now.
1950 Plymouth rear drum removal?
Block and jack up car on side to do. Remove nut and cotter pin (if there is a cotter pin) and use a wheel puller.
Will stallion donkeys mount mare horses if together in a pin?
A stallion donkey is called a Jack. A jack will try to breed a mare, but the mare may not let him cover her, even if she is in season (ovulating).
Does the ipad1 have a mic?
Yes. Its a pin hole near the head phone jack. To test use notes app to record message out skype.
How do you replace the dog bone in a toyota camry 2001?
put a jack under the engine to hold it up push the pin out should come off
Can you connect 2 separate XLR inputs to one quarter inch RCA outputs?
Normally, you can. To be clear, RCA connectors (known as phonos in Europe) are not 1/4" jacks. The two are different types of connector and for this answer, we will assume that the connector is in fact a 1/4" jack rather than RCAs. There are several wiring configurations depending on how the 1/4" jack is wired. If the jack socket carries a stereo audio signal (like a headphone output), this is the right configuration: The tip of the 1/4" jack is wired to pin 2 of the first XLR plug. The ring of the jack is wired to pin 2 of the second XLR plug Both of these should use the core of a screened cable. The screens of both cables should be connected to the sleeve of the jack. Each screen should them be connected to pins 1 and 3 of the appropriate XLR. If the jack is carrying balanced, single channel audio, this is the configuration: The tip of the jack is connected to pin 2 of the XLR plug. The ring of the XLR connects to pin 3 of the XLR and the sleeve of the jack connects to pin 1 of the XLR. To connect 2 XLRs to the same jack output, simply wire two cables into the jack and put an XLR on the end of each cable. These cover most of the common configurations but as with all things, there are exceptions to these guidelines. If there is any doubt about the way the connectors need to be wired, it's worth asking the right questions before proceeding. It might be worth mentioning that the output levels of domestic equipment tend to be lower than for professional equipment. You may find that the audio level might be lower than expected when connecting to XLR inputs.
Your wheel on your range rover is suddenly covered in oil - and hub nut loose and the retaining pin is missing - cant seem to get a spilt pin through what goes there?
jack the car up remove wheel remove hub replace bearings put it back together
What do I need to hook-up under the hood There is no power to the center pin for the trailer plug at the bumper I am trying to energize my new electric trailer jack.?
The center pin of a seven blade trailer plug is for reverse lights, not power. What type of truck is it? What trailer plug do you have...
What is a 'short pin' in bowling?
When a pin on the deck is spinning next to a single pin or the pin on the deck rolls past the single pin and does not knock it down. The reason the pin did not reach the single pin is because it is a "Short pin"
How do you replace door hinge pins on a 1993 Mercury Cougar?
Hold the end of the door with a jack, grind the head from the old pin, knock out the old pin, remove the door half of the hinge, drill out the hinge to accept the new bushings, install the new bushings, re-bolt the hinge to the door, finally, insert the new pin and install the C clip
