0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the difference between a scarf and a muffler?
A scarf goes around your head, face or neck to keep your neck/face/head warm. A muffler goes over your hands, putting your hand in each end. A scarf is a long band of fabric. A muffler is a short, round, hollow roll.
Change muffler on VW Golf?
Slice the neck off where it goes over the pipe ahead of it and slide the new one on & clamp into place. Make sure it's adusted properly before tightening as it won't loosen easily once tightened. Don't damage the inner neck taking the old muffler off.
What can the rattling from under my f150 be?
the muffler rattling? the muffler rattling? the muffler rattling?
What is a rock muffler?
A Rock muffler (or silencer in British English) is a device for reducing the amount of noise emitted by a machine.Rock muffler - rigid silencer muffler
How is muffler use in sentence?
A muffler is a device used in the exhaust system of a vehicle to reduce noise produced by the engine. In a sentence, you could say, "The mechanic replaced the old muffler with a new one to make the car quieter."
Craftsman leaf blower will not start with the muffler on it why?
The muffler is most likely clogged and will not allow the exhaust gases to exit the combustion chamber. Check the muffler for obstructions or replace the muffler.
How to change a muffler on Chevy S-10?
First off, crawl under the truck and see if your present muffler is welded on or clamped on. If it's welded on you will need to get an exhaust cutting tool from like Autozone and cut the old muffler off BUT before you do, get your new muffler and measure how far the inlet neck is and outlet neck is on the new muffler and this will tell you how far to cut. You could hold the new muffler up to the exhasut and mark how far from the muffler you need to cut. This is assumign you are replacing the bad muffler with a new one of the same size. Now there is an inlet pipe and and out let pipe on the muffler. You will also need to have the right size clamps. Pu tone clamp on the exhaust pipe going to the engine, then push the exhaust pipe into the inlet end of the muffler and slide the clamp down and snug it up but do not tighten it. Put the other clamp on the exhaust pipe towrd the rear of the truck, push the exhasut ipe into the outlet end of the muffler and then slide the clamp down onto the joint and snug up. if everythign aligns right, then tighten the clamps. Sometimes if you overtighten the clamps you will have exhaust leaks. If you cannot get the joints to seal, you may need to get your system welded. If you exhaust is leak free then you are done. After a few hot and cold cycles you may just want to crawl back under and check the bolts on the clamps just in case they came loose from the heat and cold cycles.
Why is your car emitting light fumes from the muffler?
Hole in the muffler.
How do you fix a very very loud muffler on a tecumsh riding mower engine?
Answer It could be that you need a new muffler. After so long the baffling inside the muffler can burn out. Also make sure that the muffler is not cracked or that exhaust is not leaking before it gets into the muffler. At the gasket between the muffler and the engine. Hope ths helps.
How do you repair a hole in the muffler on your 91 Chevy s10 truck?
If there is a rotted hole in the muffler please replace the muffler. However, if there is a small hole at the bottom end of the muffler it is there to allow water to escape.
Price of a muffler for a 1994 Nissan Altima?
The 1994 Nissan Altima muffler will cost approximately $50. There are several qualities of muffler's available. A stainless steel muffler will cost approximately $200.
How to fix Hole in rear bosal muffler 93 Honda civic cx?
i have a hole in my muffler right in the middle of the muffler how can i cover it
