0
I think you mean RACK and pinion backlash.
This is the amount of space between teeth in the gears of the rack and pinion which would cause a slight reverse motion before contact is re established to go forward.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is back lash with respect to rear axle?
Back lash is best described as how much the pinion gear will move before contacting and moving the crown gear. This is specified and measured on the crown gear.
What is the definition of rack and pinion?
1. Device for the conversion of rotary and linear motion, consists of a pinion and malted rock
What are the ratings and certificates for The Black Lash - 1952?
The Black Lash - 1952 is rated/received certificates of: USA:Approved USA:Passed (National Board of Review)
How do you remove the lash from a 2001 2500 Dodge 70 series rear ring pinion?
There are adjusrers on the sides of the ring gear housing for side clearance and the pinion gear depth is achieved by removing pinion gear and adding or removing shims to correct depth. should be done by an experienced technisian.v After the pinion depth is set(with shims). The backlash is set with shims under the side bearings.
Is a crown and pinion used is rock crawling?
A crown and pinion is used in the differentials in rock crawling. Most will have a very high ratio which increases power and control during very slow movements.
What are the release dates for The Black Lash - 1952?
The Black Lash - 1952 was released on: USA: 2 January 1952 Denmark: 19 April 1954 West Germany: 1957 Austria: August 1957
How do you change the pinion gears in a gm suburban?
To change the pinion gear in a differential you must first open the differential, drain the gear oil and inspect the gears and bearings. Pinion gears and ring gears are usually done as a matched set so you should plan on replacing both. Remove the axle shafts and then mark the carrier bearing caps so they can be replaced in exactly the same location and direction that they came off. remove the caps and then pull the carrier out. Measure the pinion to axle centerline distance so that you can get the new pinion in the same spot. Remove the yoke retainer nut and the driveshaft yoke and then remove the pinion from the differential housing. You should be using new bearings and races so remove the old races from the differential housing and the old bearing from the Pinion gear. The shims from the old gear should be a good starting place to set up your new pinion depth. Test fit the new pinion to see if the pinion depth is right. Install pinion bearing races, bearings and new seal. Install new ring gear and set the gear lash You may have to shim the carrier or change the pinion depth to get the right gear lash. This process usually requires expert knowledge and specialized tools and you may want to consult a qualified mechanic to do the job. There are many more detailed descriptions on the net.
Why do you feel a pop in the rear when you let off the brake on your 1998 Chevy Tahoe?
Brake shoes are hanging on the backing plate.( REAR.) bad u-joint? To much back lash in the ring and pinion gear
What rock is black?
the sedementary rock that is black is called hornblende
Did Lash Larue ever autograph his comics with just Lash?
I have met Lash at several Western film festivals and have his autograph on a photo of him on his horse. He always signed everything "Lash Larue" with a bold stroke on the "L." As to his horse's name, he always claimed it was Black Diamond although it was never mentioned in the credits or did he refer to it by name in the films. His horse in the comic books was called "Rush."
What is the black rock in the TV show LOST?
The black rock in the TV show LOST is an old ship, that is called black rock.
What is the pinion nut torque on a 1999 Chevy blazer?
There is no specific pinion nut torque. The pinion nut has to be tightened until the proper pinion preload is established. Pinion preload is what matters
