0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How can you fix a vacuum if it has no suction?
what i found out was if your vacuum doesn't have suction you need to make sure you have all the air out of the hose that is attached to you vacuum.
What is length of suction hose pipe attaching suction head with central suction unit in Miele Solaris S514 Canister Vacuum?
The length of the suction hose is around 2 feet, with an additional extender where the hose can extend up to 3 feet. with the Canister Vacuum.
What is a vacuum hose?
Its the hose that attached to a vacuum. Its where the suction is transferred from the vacuum cleaner to any attachments. Its also generically referred to as a vacuum for your car.
Skimmer open or closed to vacuum pool?
If you have a dedicated suction for the vacuum hose (illegal in Australia) then you close the skimmer to increase suction.
Can you leave the hose on a rainbow vacuum and run it on low?
If its for cleaning, then the suction will not be strong. Low mode is for air cleaning purposes.
How can you stop a vacuum cleaner making a noise?
One answer in not an inexpensive but you can purchase a central vacuum, install it in the garage and place your hose ports in your closets. the only noise you will here is the suction.
I have two side skimmers and a bottom drain i can't seem to get the correct suction to use on my vacuum hose?
lift out the skimmer basket there should be a floating diverter with a flap that closes off suction. some skimmer baskets are rotated to do the same thing. insert your hose into the other skimmer. turn off suction to the main drain if you need more suction.
How do you use pool cleaner weights?
Follow the directions for hooking up the vacuum either the one that uses the skimmer or the one that hooks up to a garden hose. Make sure all air is out of the hose and you have a good suction. Keep the vacuum head in the water. Then vacuum just like you would vacuum a carpet or floor.
What is the right length for a pool vacuum hose?
In regards to comfort and safety while swimming, yes a hose can be too long. Also, the hose might also be able to tangle and/or not allow the cleaner to move correctly and to its full reach. Lastly, The suction power needed for a longer hose would be greater; to measure suction the vacuum might have come with a neat gadget that reads this and tells you the optimal level of suction. Hope this helps! :)
What is a central vacuum system?
The main vacuum unit is usually located in the basement with tubes running throughout the house. The tubes run to each room and have a hinged cover. You insert the hose in the tube and the vacuum unit automatically turns on and you can suck up the dust. All you have to move is the hose and not the main suction unit.
Why does the pump lose its prime when the vacuum is hooked up?
You probably have air leaking through either your vac hose and/or the valve that controls your vac line. You might try replacing the gaskets on your valve stems and try a new vac hose. Also important to get the air pout of the hosing you are using to vac wuth before opening the vac line.AnswerThe pump loosing its vacuum is definitely caused by a poor seal somewhere between the suction of the pump and the suction inlet of your vacuum equipment. In the case of an above ground installation, check all connections of the hose and your vacuum apparatus.In the case of an in ground installation, you could have a crack in the pipes from the pool inlet to the isolation valve close to the pump. To check this, make sure the water level of the pool is ABOVE the connection point where you attach your vacuum hose. Set the filter up for vacuum operation WITHOUT hooking up the vacuum hose. If the pump keeps it's prime, your pipes are probably O.K. Check your vacuum hose and apparatus. If you keep the water level higher than the suction connection in the pool, even if the connection is not 100%, the pump won't loose it's prime.
How do you repair vacuum hose for Chevrolet venture 2000?
The best way to repair a vacuum hose on your Chevrolet is to replace the vacuum hose. The vacuum hose is held in place with a retaining clamp on each end of the hose.
