0
The pipe coming off of sump pump that goes outside or if allowable, a drain line.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How long of a hose can be used on a sump pump?
A sump pump discharge line should run as far from the foundation walls as possible.
Why does the sump pump motor hum but no water discharge?
Possibly the impeller needs cleaning or a blockage in the line
In sump pump discharge line check valve is installed before or after gate valve?
after gate valve, because when you want make maintenance for sump pump , you don't want all water in the pipe drop down sump pump - gate valve - non return valve
What does the check valve do in the sump pump?
It keeps the water that is pumped out from flowing back into the sump when the pump shuts off. Most sumps discharge several feet above the hole the pump sits in. If there was not a check valve the sump would just refill and pump out the water over and over.
Why does sump pump knock repeatedly after shutting off?
air in the line
Sump pump continously runs?
The sump pump could run continously for 4 different reasons:The switch is bad. The switch is what tells the pump to turn on and off, and it is possible the switch is stuck in the "on" position.The pump is undersized. If the pump is undersized the pump will not be able to keep up with the incoming water and it will continue to run.The pump discharge is restricted. The discharge pipe could be resticted, kinked, or blocked, so confirm there is flow at the end of the discharge.The pump is airbound. A pump gets airbound when the pump looses its prime and is caused by no weep hole on the discharge piping. A check valve has to be in use for this scenario to develop.
Should water of any amount be in the sump pump and would it have anything to do with my kitchen pipes being blocked.?
If you have any water at all coming into the sump, there will always be a little in the bottom unless it stays dry long enough for it to evaporate. The design of the pump doesn't let it pump the last little bit out. If there is not a check valve in the discharge pipe, what is left it the pipe going out will drain back into the sump. If the discharge pipe is connected to the house drain and there was not a check valve in that pipe, depending on where the kitchen clog is, the sink could drain into the sump.
What is Sump Pump Repair and why do I need it?
You would need a sump pump repair if the sump pump in your basement is not pumping out water. The purpose of a sump pump is to drain excess water that is part of your waterproofing system.
How To Install A Sump Pump In Your Home’s Crawl Space?
When you have a crawl space under your home, you have the possibility of having flooding or water build up. If the level of water is allowed to build up too much you can find that your home can sustain costly damage and repair issues. Installing a sump pump in your crawl space can save you from this headache. Here is a guide to help you set up a sump pump for protection. Step 1. Turn off power to the sump pump at the main power source. This will help prevent electrical shock. Step 2. A solid foundation needs to be constructed for the sump pump to rest on. This foundation is best constructed of cinder bocks or a solid piece of wood that is a little larger than the size of the pump. The foundation also needs to be level for the best results. Step 3. Drill a small hole in the discharge pipe. This will help the air flow easier through the pipe for better pressure. Install the discharge pipe from the sump pump to the area where you want to drain the excess water to. Step 4. If water begins to flow back into the sump pump, you will need to install a check flow valve or similar device. Step 5. You will need to attach the power cord for the sump pump to the discharge pipe. This cord must be secure. Step 6. Plug the power cord for the sump pump into the electricity source that you plan on using. Turn the power back on at the main power source for the sump pump to operate. Step 7. It is necessary to test the sump pump for positive operation results prior to using it. To test your sump pump fill the sump pump with water. Never test or operate your sump pump without water being present. Step 8. Add water or refill the pump until there is enough water to reach the level where the sump pump will turn on. Step 9. If you want to install a cover for your sump pump, you can do this now. These covers will help to eliminate dirt and debris from building up in your sump pump and will help to provide odor control from stagnant water.
How do you add a drain in a basement that does not have one?
its not easy but if you can locate your main drain pipe and its below your basement floor then saw cut up the floor and attach the floor drain to the trap and then tie on to the main line using the same pipe or adapters. If you have no main drain under your basement floor then you will need to saw cut a hole for a sump pump pit or basin and install the sump pump to your main drain line which has to be installed so your sump pump line runs higher then your main line before wyeing to the main line. then cut up the floor to where u want your floor drain and run the drain to your sump pump basin . Some states want a vent on your floor drain and on your sump basin so I would check what your local codes are.
Where do you install a sump pump?
Installing a sump pump yourself is a manageable DIY project that can help prevent basement flooding and water damage. Here's a step-by-step guide on how to install a sump pump: Gather Your Tools and Materials: Before you begin, ensure you have all the necessary tools and materials, including a sump pump, a sump pit, PVC pipes, a check valve, a gravel bed, a hacksaw, pipe wrenches, a level, a tape measure, a marker, a drill, concrete mix, a mixing bucket, and safety gear like gloves and goggles. Select the Installation Location: Choose an appropriate location in your basement for the sump pit. It should be in the lowest part of your basement and near a power outlet. Mark the pit's outline on the floor. Dig the Sump Pit: Using a shovel, dig a hole for the sump pit according to the marked outline. Make sure the pit is deep enough to accommodate the pump and has a slight slope towards the center. Install the Sump Pit: Place the sump pit into the hole, ensuring it is level and stable. Fill the bottom with gravel to promote proper drainage. Assemble the Pump: Follow the manufacturer's instructions to assemble the sump pump and attach the check valve to the discharge pipe. Position the pump inside the sump pit. Connect the Discharge Pipe: Use PVC pipes and connectors to run the discharge pipe from the pump to the exterior of your home. Ensure that the pipe has a gradual slope away from the house to prevent water from flowing back in. Secure the Pump and Check Valve: Fasten the pump to the pit's bottom to prevent it from shifting during operation. Secure the check valve to the discharge pipe. Test the System: Pour water into the pit to activate the pump and ensure it functions correctly. Verify that water is being pumped away from the house and that the check valve is preventing backflow. Seal the Pit: Mix concrete according to the package instructions and use it to seal the sump pit's top. This prevents odors and soil gases from entering your home. Install a Lid or Cover: To improve safety and reduce noise, consider installing a lid or cover over the sump pit. Ensure it has an access point for maintenance. Connect to Power: Plug the sump pump into a GFCI-protected electrical outlet. It's crucial to have a dedicated electrical circuit for the sump pump to ensure reliability. Regular Maintenance: Schedule regular maintenance, including cleaning the pump and checking the float switch. Test the system periodically to ensure it's ready to handle excess water when needed. Installing a sump pump yourself can be a cost-effective way to protect your home from basement flooding, but if you're uncomfortable with any part of the process or if you encounter challenges, it's advisable to consult a professional plumber for assistance. Proper installation and maintenance are essential to ensure your sump pump operates effectively when it matters most.
Why is the suction line of a pump larger than the discharge line?
It is common practice to specify the pump suction line one size larger than the pump discharge line in order to increase the Net Positive Suction Head available (NPSHA) to the pump. A smaller suction line the same pipe size as the discharge line would result in more pressure drop in the suction line and reduce the amount of head available to the suction side of the pump. This in turn would result in an operating point closer to cavitation of the pump.
