Want this question answered?
Amplifier power and impedance are not related, although a lower impedance speaker will be louder. Most home stereos cannot drive loads below 4 ohms, however, so using this 3 ohm speaker with a home theater may cause the amp to go into protection mode or shut down completely. Check your owner's manual to see what impedance of speaker your receiver can safely drive.
A speaker is a device that converts varying electrical signals into varying acoustic signals so that you can hear them as sounds.An 8 ohm speaker is a speaker that has a nominal impedance of 8 ohms. This means that is presents a load of 8 ohms to the amplifier over the range of frequencies that it is designed for. You should match the impedance of the speaker to the designed impedance of the amplifier. Failure to do so will result in inability to achieve rated power output, and it could lead to amplifier and/or speaker failure.There are other factors involved as well, such as power capacity, shape, resonant frequency, and expected enclosure design. Speaker designers spend a lot of time and money on selecting a particular speaker, and you should not arbitrarily substitute one for another without adequate justification.
What is the advantage of using an PLM
A 2 channel aplifier is an amplifier that can operate two channels. It is basically two 1-channel amplifiers in a single box. This unit is usually intended for operating a left speaker and a right speaker. A channel is the signal/power combination intended for one specific speaker. A 'Stereo' audio system typically has a left channel and a right channel. More advanced audio systems may have separate channels for different types of speakers (midrange, woofer, tweeter, very commonly subwoofer, sometimes supertweeter) or for rear channels (surround.) This sort of setup was modern during the early 90s. A bridged 2 channel amplifier is constructed in such a way that the amplifiers can be set up to operate inline providing the effect of a more powerful one-channel amplifier. If durability is a concern, a bridgeable two channel amplifier used for two channels tends to work well because it's likely to have higher quality or just more diodes so as not to be destroyed too quickly during bridged operation. Using a more powerful amplifier with the gain turned down is also a good idea if longevity is a concern.
dinosaurs
There are many downsides of using an amplifier for one's car audio system. Some downsides for using an amplifier for one's car audio system includes bothering those around them due to the noise and harming one's ears.
The main advantage of using a surround sound amplifier is to boost the sound quality of ones television. Programs sound better, and movies sound as if one is in the theatre watching the film.
input. The microphone gives a signal to the computer/radio/whatever you're using. it is input because when you speak into it,it gets in the amplifier and the amplifier processes it to came out as sound through the speaker
input. The microphone gives a signal to the computer/radio/whatever you're using. it is input because when you speak into it,it gets in the amplifier and the amplifier processes it to came out as sound through the speaker
A biderectional cable amplifier with a bypass is excellent for use with digital TV, because it amplifies the return signal. Using a unidirectional cable amplifier can result in some channels that do not work because the return signal is not amplified.
input. The microphone gives a signal to the computer/radio/whatever you're using. it is input because when you speak into it,it gets in the amplifier and the amplifier processes it to came out as sound through the speaker
Amplifier power and impedance are not related, although a lower impedance speaker will be louder. Most home stereos cannot drive loads below 4 ohms, however, so using this 3 ohm speaker with a home theater may cause the amp to go into protection mode or shut down completely. Check your owner's manual to see what impedance of speaker your receiver can safely drive.
sound travels from your source, a.k.a. in dash CD player, thru a pre-amplifier (RCA output) and then thru the rca cables that you hook up to the back of your source to the amplifier. If you are not using the pre-amp from the stereo. (RCA outputs) you can use a high level output adapter, which you connect to the speaker leads from the bacck of your source unit. The high level aka speaker level adapter changes your speaker wires on the back of your CD player to RCA outputs. from the high level adapter you then run RCA cables to your amplifier. Some amplifiers have a high level adapter built into them, which does not require the use of an external speaker level adapter, and your speaker wires can run directly into the aftermarket amplifier.
A sub from a 2.1 PC speaker system usually has the amplifier for both itself and the satellite speakers. You should be able to disconnect the satellites and use the sub by itself. You cannot use a speaker output from an amplifier to drive this sub, as the level is too high, but most surround receivers have a 'Sub Out' line level in the form an RCA jack. You can connect this using adapters to the 1/8" cable that plugs in the sub.
Try it only if the speaker is rated at 8 ohms and has sufficient power handling. Using low impedence speakers, particularly those designed for a Bose car stereo system can damage your amplifier. The speakers are not likely to have any bass response if they are used raw (outside an enclosure).
A speaker is a device that converts varying electrical signals into varying acoustic signals so that you can hear them as sounds.An 8 ohm speaker is a speaker that has a nominal impedance of 8 ohms. This means that is presents a load of 8 ohms to the amplifier over the range of frequencies that it is designed for. You should match the impedance of the speaker to the designed impedance of the amplifier. Failure to do so will result in inability to achieve rated power output, and it could lead to amplifier and/or speaker failure.There are other factors involved as well, such as power capacity, shape, resonant frequency, and expected enclosure design. Speaker designers spend a lot of time and money on selecting a particular speaker, and you should not arbitrarily substitute one for another without adequate justification.
When music is played in a stadium, using a center speaker system is the best configuration. The triangular shape of the area, with the stage at the tip, allows the sound to flow evenly throughout the venue.