0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is an apature on a camera?
opening that lets light in
Where on the camera is the aperture physically found?
It is the hole through which the light travels towards the film. The apature is not found physically as it is the name given to the size of the gap: the hole itself
What is 'apature' a synonym for?
"Aperture" is a synonym for a break or a crack. "Aperture" is used in many modern day phrases such as camera aperture and of course, "Aperture Science" from the game Portal.
What is stomata conductance?
Stomatal conductance is the speed at which water evaporates from pores in a plant, and is directly related to relative size of the stomatal apature. Basically, the higher the evaporation rate, the higher the conductance of the leaf. It must also be noted that humidity, the hydration status of the plant and light intensity are also factors that affect stomatal conductance.
What are the release dates for Regret - 2003 II?
Regret - 2003 II was released on: USA: 24 September 2003 (Apature Film Festival) USA: 9 November 2003 (San Francisco Korean American Film Festival) USA: 8 March 2004 (San Francisco International Asian American Film Festival) USA: 8 August 2004 (Urbanworld Film Festival) USA: 11 November 2004 (San Diego Asian Film Festival)
What is the best phone to buy?
The best phone to buy these days would be the iPhone4S.Reasons to buy:The New Features:The New retina display on the phone look bright8MP camera and 1080p video recording with all new LED flash with new gyro to make your video stabilize and look a lot smoother. New optics withcamera: Increase the size of the apature to let more light in and they added a 5th lense so that there is a sharper image overall.Dual Core A5 Chip (On iPad2)Siri Personal AssistantiOS5 Apple update (with over 200 new features)Siri can do math, read your texts and even set appointments with it.
Replacing a radiator on a fiat punto grande 08?
Remove the top and bottom hoses Remove the expansion bottle (2 bolts ) and place to one side Disconnect the fan multi plug The fan needs to be removed by pushing in the top clips where the fan housing slots into the rad. After pushing the black blips lift the fan housing up and away from the rad (work underneath to do this) Remove the front grill comes out easy its just a push fit. Once the grill is removed and working through the apature and looking at the top left and right of the rad remove the 2 torx bolts . Move to the underside once again, You will now be able to lift the rad up and out of the 2 bottom locating holes No need to remove bumper
Why is oil used in microscopy?
Oil is used in microscopy because air Can't bend light enough. It's hard to explain in words, but, you know how when you put a stick in water, it appears bent? well in simple terms, oil bends it more, and the information (image information) increaces. It's kind of like having a bigger telescope, the oil increases the apature of the lens you are using, it gathers more information for the eyepiece to magnify, therefore you see more. If you want a detailed explination, please post again.
How-to fit a car front windscreen with rubber window seals?
These instructions are not for bonded windscreens but are for rubber seals. Firstly please think of the type of glass you are handeling, If this is toughend glass it will take a bit of banging around the edge with your hand which helps when fitting. If it is laminated be very careful as one bang in the wrong place will crack it. There are two basic types of rubber seal one type has a slot to fit the car appature and a slot for the glass to fit in, which are opposite each other. There will also be a slot for a key rubber. This rubber seal is fitted around the car appature first, it can be held in place with masking tape from the car body round the rubber and onto the trim inside. If the rubber has two ends make sure these fit together perfectly with some glazing sealant or if you can align the rubber superglue is good. Attempt to fit the bottom corner of the glass into bottom slot of the rubber and push the glass as close to the corner as possible, with a modified screwdriver (eg with all the sharp edges taken of ) begin to work the rubber over the glass carefully around the bottom corners make sure the glass is well down in the slot and then work upward on each side of the glass and then along the top, again if this is toughend glass you can help it in with a few bangs from you hand, if laminated try a little soapy water and let it go in with care. Sealant can be applied around the slots at this stage if required and then a special tool is required to insert the key rubber. The second type of rubber has a slot that fits the glass and a flange that pulls over the car windscreen appature. This rubber is usually prejoined. This rubber must be fitted around the glass first, you can use masking tape to secure the rubber as this can be removed as you are fitting. With the rubber fitted to the glass you need some strong thinnish cord or electrical wire or string, the size of picture cord. You want enough to go around the window twice idealy. Insert the cord starting at the bottom centre of the windscreen flange feeding the cord under the flang twice round, have about 2" hanging out at the bottom. Find yourself a friend and lift the windscreen into position against the apature making sure the two string ends are inside the car. Someone needs to be in the car and begin to pull the string and this will pull the rubber flange over the car appature. Try and get the bottom seated, lightly pushing the glass from outside will help, but be carefull because the glass that uses this type of rubber could be laminated, also with the cord twice round the rubber you get two goes at pulling the rubber over the car appature. The glass should be marked in one corner wether it is toughend or laminated.
